sono nuovo del forum ed un noob di Linux, Il mio problema riguarda OpenWRT, che non è Ubuntu, ma in Italia non ci sono forum specifici e non sono riuscito a trovare risposta da nessuna parte. Quindi mi scuso in partenza, ma chiedo a voi perchè credo che il problema sia risolvibile conoscendo un minimo di Linux (che io non ho
).In pratica ho installato con successo (che fatica...) mediante SSH e Telnet l'ultima versione (poi aggiornata) di OpenWRT sul router TP-LINK MR3220.
Sono riuscito ad installare l'interfaccia grafica LUCI e settare la connessione ad internet mediate l'altro router di casa. Quindi ho anche installato tutti i driver per la porta USB di cui è dotato il router.
Poi ho installato il pacchetto FOWSR tramite appunto "opkg fowsr" che dovrebbe essere un programma che si connette ad una stazione meteo amatoriale, ne legge i dati e li trasmette su internet a Wunderground. Questo viene fatto da altre persone con successo, si legge in rete.
Il mio problema è che lanciando il programma fowsr pare che la periferica USB non venga riconosciuta e non capisco perchè, infatti ho seguito i passi indicati in rete da chi ha già fatto questo e la periferica non nasce con driver specifici.
Il risultato che ottengo è:
Uploaded with ImageShack.us
Se lancioo "dmesg" ottengo questo risultato:
Codice: Seleziona tutto
root@OpenWrt:~# dmesg
[ 0.000000] Linux version 3.3.8 (openwrt@msk-qdisc1.noc.yandex.net) (gcc version 4.6.3 20120201 (prerelease) (Linaro GCC 4.6-2012.02) ) #1 Tue Jul 3 06:05:27 MSK 2012
[ 0.000000] MyLoader: sysp=f0f0f0f0, boardp=f0f0f0f0, parts=f0f0f0f0
[ 0.000000] bootconsole [early0] enabled
[ 0.000000] CPU revision is: 00019374 (MIPS 24Kc)
[ 0.000000] SoC: Atheros AR7241 rev 1
[ 0.000000] Clocks: CPU:400.000MHz, DDR:400.000MHz, AHB:200.000MHz, Ref:5.000MHz
[ 0.000000] Determined physical RAM map:
[ 0.000000] memory: 02000000 @ 00000000 (usable)
[ 0.000000] Initrd not found or empty - disabling initrd
[ 0.000000] Zone PFN ranges:
[ 0.000000] Normal 0x00000000 -> 0x00002000
[ 0.000000] Movable zone start PFN for each node
[ 0.000000] Early memory PFN ranges
[ 0.000000] 0: 0x00000000 -> 0x00002000
[ 0.000000] On node 0 totalpages: 8192
[ 0.000000] free_area_init_node: node 0, pgdat 80316500, node_mem_map 81000000
[ 0.000000] Normal zone: 64 pages used for memmap
[ 0.000000] Normal zone: 0 pages reserved
[ 0.000000] Normal zone: 8128 pages, LIFO batch:0
[ 0.000000] pcpu-alloc: s0 r0 d32768 u32768 alloc=1*32768
[ 0.000000] pcpu-alloc: [0] 0
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 8128
[ 0.000000] Kernel command line: board=TL-MR3220 console=ttyS0,115200 rootfstype=squashfs,jffs2 noinitrd
[ 0.000000] PID hash table entries: 128 (order: -3, 512 bytes)
[ 0.000000] Dentry cache hash table entries: 4096 (order: 2, 16384 bytes)
[ 0.000000] Inode-cache hash table entries: 2048 (order: 1, 8192 bytes)
[ 0.000000] Primary instruction cache 64kB, VIPT, 4-way, linesize 32 bytes.
[ 0.000000] Primary data cache 32kB, 4-way, VIPT, cache aliases, linesize 32 bytes
[ 0.000000] Writing ErrCtl register=00000000
[ 0.000000] Readback ErrCtl register=00000000
[ 0.000000] Memory: 28988k/32768k available (2204k kernel code, 3780k reserved, 573k data, 204k init, 0k highmem)
[ 0.000000] SLUB: Genslabs=9, HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
[ 0.000000] NR_IRQS:48
[ 0.000000] Calibrating delay loop... 265.42 BogoMIPS (lpj=1327104)
[ 0.080000] pid_max: default: 32768 minimum: 301
[ 0.080000] Mount-cache hash table entries: 512
[ 0.090000] NET: Registered protocol family 16
[ 0.090000] gpiochip_add: registered GPIOs 0 to 17 on device: ath79
[ 0.100000] MIPS: machine is TP-LINK TL-MR3220
[ 0.500000] registering PCI controller with io_map_base unset
[ 0.540000] bio: create slab <bio-0> at 0
[ 0.550000] PCI host bridge to bus 0000:00
[ 0.550000] pci_bus 0000:00: root bus resource [mem 0x10000000-0x17ffffff]
[ 0.560000] pci_bus 0000:00: root bus resource [io 0x0000]
[ 0.560000] pci 0000:00:00.0: [168c:002b] type 0 class 0x000280
[ 0.560000] pci 0000:00:00.0: fixup device configuration
[ 0.570000] pci 0000:00:00.0: reg 10: [mem 0x10000000-0x1000ffff 64bit]
[ 0.570000] pci 0000:00:00.0: supports D1
[ 0.570000] pci 0000:00:00.0: PME# supported from D0 D1 D3hot
[ 0.570000] pci 0000:00:00.0: BAR 0: assigned [mem 0x10000000-0x1000ffff 64bit]
[ 0.570000] pci 0000:00:00.0: using irq 40 for pin 1
[ 0.580000] Switching to clocksource MIPS
[ 0.580000] NET: Registered protocol family 2
[ 0.590000] IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.590000] TCP established hash table entries: 1024 (order: 1, 8192 bytes)
[ 0.600000] TCP bind hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.600000] TCP: Hash tables configured (established 1024 bind 1024)
[ 0.610000] TCP reno registered
[ 0.610000] UDP hash table entries: 256 (order: 0, 4096 bytes)
[ 0.620000] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
[ 0.630000] NET: Registered protocol family 1
[ 0.630000] PCI: CLS 0 bytes, default 32
[ 0.650000] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[ 0.650000] JFFS2 version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
[ 0.660000] msgmni has been set to 56
[ 0.670000] io scheduler noop registered
[ 0.670000] io scheduler deadline registered (default)
[ 0.680000] Serial: 8250/16550 driver, 16 ports, IRQ sharing enabled
[ 0.710000] serial8250.0: ttyS0 at MMIO 0x18020000 (irq = 11) is a 16550A
[ 0.720000] console [ttyS0] enabled, bootconsole disabled
[ 0.730000] m25p80 spi0.0: found en25f32, expected m25p80
[ 0.740000] m25p80 spi0.0: en25f32 (4096 Kbytes)
[ 0.740000] 5 tp-link partitions found on MTD device spi0.0
[ 0.750000] Creating 5 MTD partitions on "spi0.0":
[ 0.750000] 0x000000000000-0x000000020000 : "u-boot"
[ 0.760000] 0x000000020000-0x00000011d800 : "kernel"
[ 0.760000] mtd: partition "kernel" must either start or end on erase block boundary or be smaller than an erase block -- forcing read-only
[ 0.780000] 0x00000011d800-0x0000003f0000 : "rootfs"
[ 0.780000] mtd: partition "rootfs" must either start or end on erase block boundary or be smaller than an erase block -- forcing read-only
[ 0.800000] mtd: partition "rootfs" set to be root filesystem
[ 0.800000] mtd: partition "rootfs_data" created automatically, ofs=290000, len=160000
[ 0.810000] 0x000000290000-0x0000003f0000 : "rootfs_data"
[ 0.820000] 0x0000003f0000-0x000000400000 : "art"
[ 0.830000] 0x000000020000-0x0000003f0000 : "firmware"
[ 1.080000] ag71xx_mdio: probed
[ 1.080000] eth0: Atheros AG71xx at 0xba000000, irq 5
[ 1.680000] eth0: Found an AR7240/AR9330 built-in switch
[ 2.910000] eth1: Atheros AG71xx at 0xb9000000, irq 4
[ 3.520000] ag71xx ag71xx.0: eth1: connected to PHY at ag71xx-mdio.1:04 [uid=004dd041, driver=Generic PHY]
[ 3.530000] TCP cubic registered
[ 3.530000] NET: Registered protocol family 17
[ 3.530000] Bridge firewalling registered
[ 3.540000] 8021q: 802.1Q VLAN Support v1.8
[ 3.550000] VFS: Mounted root (squashfs filesystem) readonly on device 31:2.
[ 3.560000] Freeing unused kernel memory: 204k freed
[ 6.830000] Registered led device: tp-link:green:system
[ 6.830000] Registered led device: tp-link:green:qss
[ 6.830000] Registered led device: tp-link:green:3g
[ 7.500000] eth0: link up (1000Mbps/Full duplex)
[ 10.160000] JFFS2 notice: (446) jffs2_build_xattr_subsystem: complete building xattr subsystem, 17 of xdatum (1 unchecked, 16 orphan) and 30 of xref (0 dead, 18 orphan) found.
[ 10.370000] eth0: link down
[ 11.700000] Compat-wireless backport release: compat-wireless-2012-06-14
[ 11.700000] Backport based on wireless-testing.git master-2012-06-14
[ 11.710000] compat.git: wireless-testing.git
[ 11.870000] cfg80211: Calling CRDA to update world regulatory domain
[ 11.880000] cfg80211: World regulatory domain updated:
[ 11.890000] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
[ 11.890000] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[ 11.900000] cfg80211: (2457000 KHz - 2482000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
[ 11.910000] cfg80211: (2474000 KHz - 2494000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
[ 11.920000] cfg80211: (5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[ 11.920000] cfg80211: (5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[ 12.130000] usbcore: registered new interface driver usbfs
[ 12.130000] usbcore: registered new interface driver hub
[ 12.140000] usbcore: registered new device driver usb
[ 12.600000] PCI: Enabling device 0000:00:00.0 (0000 -> 0002)
[ 12.620000] ath: EEPROM regdomain: 0x0
[ 12.620000] ath: EEPROM indicates default country code should be used
[ 12.620000] ath: doing EEPROM country->regdmn map search
[ 12.620000] ath: country maps to regdmn code: 0x3a
[ 12.620000] ath: Country alpha2 being used: US
[ 12.620000] ath: Regpair used: 0x3a
[ 12.620000] ieee80211 phy0: Selected rate control algorithm 'minstrel_ht'
[ 12.620000] Registered led device: ath9k-phy0
[ 12.620000] ieee80211 phy0: Atheros AR9285 Rev:2 mem=0xb0000000, irq=40
[ 12.630000] cfg80211: Calling CRDA for country: US
[ 12.640000] cfg80211: Regulatory domain changed to country: US
[ 12.640000] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
[ 12.650000] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2700 mBm)
[ 12.660000] cfg80211: (5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 1700 mBm)
[ 12.670000] cfg80211: (5250000 KHz - 5330000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[ 12.670000] cfg80211: (5490000 KHz - 5600000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[ 12.680000] cfg80211: (5650000 KHz - 5710000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[ 12.690000] cfg80211: (5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 3000 mBm)
[ 12.740000] PPP generic driver version 2.4.2
[ 12.900000] ip_tables: (C) 2000-2006 Netfilter Core Team
[ 13.020000] NET: Registered protocol family 24
[ 13.040000] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 13.050000] ehci-platform ehci-platform: Generic Platform EHCI Controller
[ 13.050000] ehci-platform ehci-platform: new USB bus registered, assigned bus number 1
[ 13.090000] ehci-platform ehci-platform: irq 3, io mem 0x1b000000
[ 13.110000] ehci-platform ehci-platform: USB 2.0 started, EHCI 1.00
[ 13.110000] hub 1-0:1.0: USB hub found
[ 13.120000] hub 1-0:1.0: 1 port detected
[ 13.140000] nf_conntrack version 0.5.0 (456 buckets, 1824 max)
[ 13.480000] usb 1-1: new low-speed USB device number 2 using ehci-platform
[ 18.420000] device eth0 entered promiscuous mode
[ 19.120000] eth0: link up (1000Mbps/Full duplex)
[ 19.120000] br-lan: port 1(eth0) entered forwarding state
[ 19.130000] br-lan: port 1(eth0) entered forwarding state
[ 21.130000] br-lan: port 1(eth0) entered forwarding state
[ 21.300000] device wlan0 entered promiscuous mode
[ 21.670000] br-lan: port 2(wlan0) entered forwarding state
[ 21.680000] br-lan: port 2(wlan0) entered forwarding state
[ 23.680000] br-lan: port 2(wlan0) entered forwarding state
[ 229.080000] uhci_hcd: USB Universal Host Controller Interface driver
[ 310.460000] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) DriverIn pratica sembra che ci sia qualche problema con i driver USB, che però gli altri non hanno avuto...
Ho provato di tutto:
reset memoria da stazione,
tolto e rimesso batterie,
reset stazione da pc,
riavviato tp-link,
reinstallato più e più volte i driver usb generici,
ri-editato il file wunderground.sh che conteneva dei "^M" problematici
....ma niente non ne vuol sapere di partire (cioè riconoscere la stazione).
Sono giorni che mi spacco la testa su questa cosa e non ne riesco a venirne fuori
Grazie mille a tutti dell'aiuto che vorrete concedermi!!!
