installazione scanner di rete Lexmark x464

Riconoscimento, installazione e configurazione delle periferiche.

Re: installazione scanner di rete Lexmark x464

Messaggioda magozurlinux » giovedì 5 luglio 2018, 11:59

Con Linux dovrebbe funzionare con xsane.

Da terminale con la multifunzione Lexmark accesa postami questo comando:

Codice: Seleziona tutto
sudo lsusb -v -d 043d:0169
XUBUNTU 16.04 LTS x86_64 Desktop :ciao:
Avatar utente
magozurlinux
Accecante Asceta
Accecante Asceta
 
Messaggi: 20098
Iscrizione: marzo 2010
Località: Pisa
Desktop: Desktop
Distribuzione: Xubuntu 16.04 LTS x86_64

Re: installazione scanner di rete Lexmark x464

Messaggioda alle9 » venerdì 6 luglio 2018, 11:14

Codice: Seleziona tutto
alex@alex-LIFEBOOK-A512:~$ sudo lsusb -v -d 043d:0169
[sudo] password di alex:

Bus 002 Device 005: ID 043d:0169 Lexmark International, Inc.
Device Descriptor:
  bLength                18
  bDescriptorType         1
  bcdUSB               2.00
  bDeviceClass            0 (Defined at Interface level)
  bDeviceSubClass         0
  bDeviceProtocol         0
  bMaxPacketSize0        64
  idVendor           0x043d Lexmark International, Inc.
  idProduct          0x0169
  bcdDevice            0.00
  iManufacturer           1 Lexmark International
  iProduct                2 Lexmark X464de
  iSerial                 3 35P9ZP5
  bNumConfigurations      1
  Configuration Descriptor:
    bLength                 9
    bDescriptorType         2
    wTotalLength           80
    bNumInterfaces          3
    bConfigurationValue     1
    iConfiguration          0
    bmAttributes         0xc0
      Self Powered
    MaxPower                2mA
    Interface Descriptor:
      bLength                 9
      bDescriptorType         4
      bInterfaceNumber        0
      bAlternateSetting       0
      bNumEndpoints           2
      bInterfaceClass       255 Vendor Specific Class
      bInterfaceSubClass    255 Vendor Specific Subclass
      bInterfaceProtocol    255 Vendor Specific Protocol
      iInterface              5 Scan
      Endpoint Descriptor:
        bLength                 7                                                                                                                                                               
        bDescriptorType         5                                                                                                                                                               
        bEndpointAddress     0x02  EP 2 OUT                                                                                                                                                     
        bmAttributes            2
          Transfer Type            Bulk
          Synch Type               None
          Usage Type               Data
        wMaxPacketSize     0x0200  1x 512 bytes
        bInterval               0
      Endpoint Descriptor:
        bLength                 7
        bDescriptorType         5
        bEndpointAddress     0x89  EP 9 IN
        bmAttributes            2
          Transfer Type            Bulk
          Synch Type               None
          Usage Type               Data
        wMaxPacketSize     0x0200  1x 512 bytes
        bInterval               0
    Interface Descriptor:
      bLength                 9
      bDescriptorType         4
      bInterfaceNumber        1
      bAlternateSetting       0
      bNumEndpoints           2
      bInterfaceClass         7 Printer
      bInterfaceSubClass      1 Printer
      bInterfaceProtocol      2 Bidirectional
      iInterface              4 Print
      Endpoint Descriptor:
        bLength                 7
        bDescriptorType         5
        bEndpointAddress     0x88  EP 8 IN
        bmAttributes            2
          Transfer Type            Bulk
          Synch Type               None
          Usage Type               Data
        wMaxPacketSize     0x0200  1x 512 bytes
        bInterval               0
      Endpoint Descriptor:
        bLength                 7
        bDescriptorType         5
        bEndpointAddress     0x01  EP 1 OUT
        bmAttributes            2
          Transfer Type            Bulk
          Synch Type               None
          Usage Type               Data
        wMaxPacketSize     0x0200  1x 512 bytes
        bInterval               0
    Interface Descriptor:
      bLength                 9
      bDescriptorType         4
      bInterfaceNumber        2
      bAlternateSetting       0
      bNumEndpoints           1
      bInterfaceClass         3 Human Interface Device
      bInterfaceSubClass      0 No Subclass
      bInterfaceProtocol      0 None
      iInterface              6 HID
        HID Device Descriptor:
          bLength                 9
          bDescriptorType        33
          bcdHID               1.00
          bCountryCode            0 Not supported
          bNumDescriptors         1
          bDescriptorType        34 Report
          wDescriptorLength      73
         Report Descriptors:
           ** UNAVAILABLE **
      Endpoint Descriptor:
        bLength                 7
        bDescriptorType         5
        bEndpointAddress     0x8b  EP 11 IN
        bmAttributes            3
          Transfer Type            Interrupt
          Synch Type               None
          Usage Type               Data
        wMaxPacketSize     0x0040  1x 64 bytes
        bInterval              16
Device Qualifier (for other device speed):
  bLength                10
  bDescriptorType         6
  bcdUSB               2.00
  bDeviceClass            0 (Defined at Interface level)
  bDeviceSubClass         0
  bDeviceProtocol         0
  bMaxPacketSize0        64
  bNumConfigurations      1
Device Status:     0x0001
  Self Powered
Avatar utente
alle9
Scoppiettante Seguace
Scoppiettante Seguace
 
Messaggi: 937
Iscrizione: ottobre 2006
Località: macerata - Italy
Desktop: plasma
Distribuzione: Ubuntu 18.04 x86_64
Sesso: Maschile

Re: installazione scanner di rete Lexmark x464

Messaggioda magozurlinux » venerdì 6 luglio 2018, 12:03

Da terminale dai questi comandi:

Codice: Seleziona tutto
sudo -H gedit /lib/udev/rules.d/60-libsane1.rules


prima di LABEL="libsane_rules_end" copia e incolla queste righe:

Codice: Seleziona tutto
# Lexmark X464
ATTRS{idVendor}=="043d", ATTRS{idProduct}=="0169", MODE="664", GROUP="scanner", ENV{libsane_matched}="yes"


salva ed esci dall'editor di testo.

Codice: Seleziona tutto
sudo -H gedit /etc/sane.d/lexmark.conf


scorri il file, posizionati sull'ultimo modello di scanner lexmark, premi Invio ed aggiungi sotto queste righe:

Codice: Seleziona tutto
# Samsung X454
usb 0x043d 0x0169


salva ed esci dall'editor di testo.

Codice: Seleziona tutto
sudo service udev restart


riavvia il pc.

Prova lo scanner.

Da terminale postami questo comando:

Codice: Seleziona tutto
dpkg -l | grep lexmark
XUBUNTU 16.04 LTS x86_64 Desktop :ciao:
Avatar utente
magozurlinux
Accecante Asceta
Accecante Asceta
 
Messaggi: 20098
Iscrizione: marzo 2010
Località: Pisa
Desktop: Desktop
Distribuzione: Xubuntu 16.04 LTS x86_64

Re: installazione scanner di rete Lexmark x464

Messaggioda alle9 » lunedì 9 luglio 2018, 12:56

Codice: Seleziona tutto
alex@alex-LIFEBOOK-A512:~$ dpkg -l | grep lexmark
ii  lexmark-network-scan                            2.0.0.0-2                                   amd64        Lexmark Network and USB Scan Drivers software
alex@alex-LIFEBOOK-A512:~$


ma lo scanner sane non lo vede ancora :muro:
Avatar utente
alle9
Scoppiettante Seguace
Scoppiettante Seguace
 
Messaggi: 937
Iscrizione: ottobre 2006
Località: macerata - Italy
Desktop: plasma
Distribuzione: Ubuntu 18.04 x86_64
Sesso: Maschile

Re: installazione scanner di rete Lexmark x464

Messaggioda magozurlinux » lunedì 9 luglio 2018, 17:33

Ciao.

La multifunzione Lexmark è ancora collegata ad una porta usb?

Proviamo col debug:

da terminale dai questo comando:

Codice: Seleziona tutto
export SANE_DEBUG_DLL=255


da terminale postami questo comando

Codice: Seleziona tutto
scanimage --test
XUBUNTU 16.04 LTS x86_64 Desktop :ciao:
Avatar utente
magozurlinux
Accecante Asceta
Accecante Asceta
 
Messaggi: 20098
Iscrizione: marzo 2010
Località: Pisa
Desktop: Desktop
Distribuzione: Xubuntu 16.04 LTS x86_64

Re: installazione scanner di rete Lexmark x464

Messaggioda supertack » martedì 10 luglio 2018, 0:57

Detto che ci sono riuscito tempo fa su pc con Debian e dopo smanettamenti vari (non replicabili su altro pc identico tra l'altro) ti dico che devi installare e avviare il demone sane.d.
In alternativa, ho configurato il profilo sulla stampante di invio in una cartella condivisa del pc, ho fatto tutto dal pannello di controllo web della stampante e funziona perfettamente.
supertack
Prode Principiante
 
Messaggi: 74
Iscrizione: dicembre 2011

Re: installazione scanner di rete Lexmark x464

Messaggioda alle9 » mercoledì 11 luglio 2018, 16:48

Codice: Seleziona tutto
alex@alex-LIFEBOOK-A512:~$ scanimage --test
[sanei_debug] Setting debug level of dll to 255.
[dll] sane_init: SANE dll backend version 1.0.13 from sane-backends 1.0.27
[dll] sane_init/read_dlld: attempting to open directory `./dll.d'
[dll] sane_init/read_dlld: attempting to open directory `/etc/sane.d/dll.d'
[dll] sane_init/read_dlld: using config directory `/etc/sane.d/dll.d'
[dll] sane_init/read_dlld: considering /etc/sane.d/dll.d/hplip
[dll] sane_init/read_config: reading dll.d/hplip
[dll] add_backend: adding backend `hpaio'
[dll] sane_init/read_dlld: considering /etc/sane.d/dll.d/libsane-extras
[dll] sane_init/read_config: reading dll.d/libsane-extras
[dll] add_backend: adding backend `ls5000'
[dll] sane_init/read_dlld: done.
[dll] sane_init/read_config: reading dll.conf
[dll] add_backend: adding backend `net'
[dll] add_backend: adding backend `abaton'
[dll] add_backend: adding backend `agfafocus'
[dll] add_backend: adding backend `apple'
[dll] add_backend: adding backend `avision'
[dll] add_backend: adding backend `artec'
[dll] add_backend: adding backend `artec_eplus48u'
[dll] add_backend: adding backend `as6e'
[dll] add_backend: adding backend `bh'
[dll] add_backend: adding backend `canon'
[dll] add_backend: adding backend `canon630u'
[dll] add_backend: adding backend `canon_dr'
[dll] add_backend: adding backend `cardscan'
[dll] add_backend: adding backend `coolscan'
[dll] add_backend: adding backend `coolscan3'
[dll] add_backend: adding backend `dell1600n_net'
[dll] add_backend: adding backend `dmc'
[dll] add_backend: adding backend `epjitsu'
[dll] add_backend: adding backend `epson2'
[dll] add_backend: adding backend `epsonds'
[dll] add_backend: adding backend `fujitsu'
[dll] add_backend: adding backend `genesys'
[dll] add_backend: adding backend `gt68xx'
[dll] add_backend: adding backend `hp'                                                                                                                                                         
[dll] add_backend: adding backend `hp3900'                                                                                                                                                     
[dll] add_backend: adding backend `hpsj5s'                                                                                                                                                     
[dll] add_backend: adding backend `hp3500'
[dll] add_backend: adding backend `hp4200'
[dll] add_backend: adding backend `hp5400'
[dll] add_backend: adding backend `hp5590'
[dll] add_backend: adding backend `hpljm1005'
[dll] add_backend: adding backend `hs2p'
[dll] add_backend: adding backend `ibm'
[dll] add_backend: adding backend `kodak'
[dll] add_backend: adding backend `kodakaio'
[dll] add_backend: adding backend `kvs1025'
[dll] add_backend: adding backend `kvs20xx'
[dll] add_backend: adding backend `leo'
[dll] add_backend: adding backend `lexmark'
[dll] add_backend: adding backend `ma1509'
[dll] add_backend: adding backend `magicolor'
[dll] add_backend: adding backend `matsushita'
[dll] add_backend: adding backend `microtek'
[dll] add_backend: adding backend `microtek2'
[dll] add_backend: adding backend `mustek'
[dll] add_backend: adding backend `mustek_usb'
[dll] add_backend: adding backend `mustek_usb2'
[dll] add_backend: adding backend `nec'
[dll] add_backend: adding backend `niash'
[dll] add_backend: adding backend `pie'
[dll] add_backend: adding backend `pint'
[dll] add_backend: adding backend `pixma'
[dll] add_backend: adding backend `plustek'
[dll] add_backend: adding backend `qcam'
[dll] add_backend: adding backend `ricoh'
[dll] add_backend: adding backend `rts8891'
[dll] add_backend: adding backend `s9036'
[dll] add_backend: adding backend `sceptre'
[dll] add_backend: adding backend `sharp'
[dll] add_backend: adding backend `sm3600'
[dll] add_backend: adding backend `sm3840'
[dll] add_backend: adding backend `snapscan'
[dll] add_backend: adding backend `sp15c'
[dll] add_backend: adding backend `tamarack'
[dll] add_backend: adding backend `teco1'
[dll] add_backend: adding backend `teco2'
[dll] add_backend: adding backend `teco3'
[dll] add_backend: adding backend `u12'
[dll] add_backend: adding backend `umax'
[dll] add_backend: adding backend `umax1220u'
[dll] add_backend: adding backend `v4l'
[dll] add_backend: adding backend `xerox_mfp'
[dll] add_backend: adding backend `lexmark_nscan'
[dll] sane_get_devices
[dll] load: searching backend `lexmark_nscan' in `/usr/lib/x86_64-linux-gnu/sane'
[dll] load: trying to load `/usr/lib/x86_64-linux-gnu/sane/libsane-lexmark_nscan.so.1'
[dll] load: couldn't open `/usr/lib/x86_64-linux-gnu/sane/libsane-lexmark_nscan.so.1' (No such file or directory)
[dll] load: couldn't find backend `lexmark_nscan' (No such file or directory)
[dll] load: searching backend `xerox_mfp' in `/usr/lib/x86_64-linux-gnu/sane'
[dll] load: trying to load `/usr/lib/x86_64-linux-gnu/sane/libsane-xerox_mfp.so.1'
[dll] load: dlopen()ing `/usr/lib/x86_64-linux-gnu/sane/libsane-xerox_mfp.so.1'
[dll] init: initializing backend `xerox_mfp'
[dll] init: backend `xerox_mfp' is version 1.0.13
[dll] load: searching backend `v4l' in `/usr/lib/x86_64-linux-gnu/sane'
[dll] load: trying to load `/usr/lib/x86_64-linux-gnu/sane/libsane-v4l.so.1'
[dll] load: couldn't open `/usr/lib/x86_64-linux-gnu/sane/libsane-v4l.so.1' (No such file or directory)
[dll] load: couldn't find backend `v4l' (No such file or directory)
[dll] load: searching backend `umax1220u' in `/usr/lib/x86_64-linux-gnu/sane'
[dll] load: trying to load `/usr/lib/x86_64-linux-gnu/sane/libsane-umax1220u.so.1'
[dll] load: dlopen()ing `/usr/lib/x86_64-linux-gnu/sane/libsane-umax1220u.so.1'
[dll] init: initializing backend `umax1220u'
[dll] init: backend `umax1220u' is version 1.0.2
[dll] load: searching backend `umax' in `/usr/lib/x86_64-linux-gnu/sane'
[dll] load: trying to load `/usr/lib/x86_64-linux-gnu/sane/libsane-umax.so.1'
[dll] load: dlopen()ing `/usr/lib/x86_64-linux-gnu/sane/libsane-umax.so.1'
[dll] init: initializing backend `umax'
[dll] init: backend `umax' is version 1.0.45
[dll] load: searching backend `u12' in `/usr/lib/x86_64-linux-gnu/sane'
[dll] load: trying to load `/usr/lib/x86_64-linux-gnu/sane/libsane-u12.so.1'
[dll] load: dlopen()ing `/usr/lib/x86_64-linux-gnu/sane/libsane-u12.so.1'
[dll] init: initializing backend `u12'
[dll] init: backend `u12' is version 1.0.0
[dll] load: searching backend `teco3' in `/usr/lib/x86_64-linux-gnu/sane'
[dll] load: trying to load `/usr/lib/x86_64-linux-gnu/sane/libsane-teco3.so.1'
[dll] load: dlopen()ing `/usr/lib/x86_64-linux-gnu/sane/libsane-teco3.so.1'
[dll] init: initializing backend `teco3'
[dll] init: backend `teco3' is version 1.0.1
[dll] load: searching backend `teco2' in `/usr/lib/x86_64-linux-gnu/sane'
[dll] load: trying to load `/usr/lib/x86_64-linux-gnu/sane/libsane-teco2.so.1'
[dll] load: dlopen()ing `/usr/lib/x86_64-linux-gnu/sane/libsane-teco2.so.1'
[dll] init: initializing backend `teco2'
[dll] init: backend `teco2' is version 1.0.10
[dll] load: searching backend `teco1' in `/usr/lib/x86_64-linux-gnu/sane'
[dll] load: trying to load `/usr/lib/x86_64-linux-gnu/sane/libsane-teco1.so.1'
[dll] load: dlopen()ing `/usr/lib/x86_64-linux-gnu/sane/libsane-teco1.so.1'
[dll] init: initializing backend `teco1'
[dll] init: backend `teco1' is version 1.0.10
[dll] load: searching backend `tamarack' in `/usr/lib/x86_64-linux-gnu/sane'
[dll] load: trying to load `/usr/lib/x86_64-linux-gnu/sane/libsane-tamarack.so.1'
[dll] load: dlopen()ing `/usr/lib/x86_64-linux-gnu/sane/libsane-tamarack.so.1'
[dll] init: initializing backend `tamarack'
[dll] init: backend `tamarack' is version 1.0.0
[dll] load: searching backend `sp15c' in `/usr/lib/x86_64-linux-gnu/sane'
[dll] load: trying to load `/usr/lib/x86_64-linux-gnu/sane/libsane-sp15c.so.1'
[dll] load: dlopen()ing `/usr/lib/x86_64-linux-gnu/sane/libsane-sp15c.so.1'
[dll] init: initializing backend `sp15c'
[dll] init: backend `sp15c' is version 1.0.0
[dll] load: searching backend `snapscan' in `/usr/lib/x86_64-linux-gnu/sane'
[dll] load: trying to load `/usr/lib/x86_64-linux-gnu/sane/libsane-snapscan.so.1'
[dll] load: dlopen()ing `/usr/lib/x86_64-linux-gnu/sane/libsane-snapscan.so.1'
[dll] init: initializing backend `snapscan'
[dll] init: backend `snapscan' is version 1.4.53
[dll] load: searching backend `sm3840' in `/usr/lib/x86_64-linux-gnu/sane'
[dll] load: trying to load `/usr/lib/x86_64-linux-gnu/sane/libsane-sm3840.so.1'
[dll] load: dlopen()ing `/usr/lib/x86_64-linux-gnu/sane/libsane-sm3840.so.1'
[dll] init: initializing backend `sm3840'
[dll] init: backend `sm3840' is version 1.0.0
[dll] load: searching backend `sm3600' in `/usr/lib/x86_64-linux-gnu/sane'
[dll] load: trying to load `/usr/lib/x86_64-linux-gnu/sane/libsane-sm3600.so.1'
[dll] load: dlopen()ing `/usr/lib/x86_64-linux-gnu/sane/libsane-sm3600.so.1'
[dll] init: initializing backend `sm3600'
[dll] init: backend `sm3600' is version 1.0.6
[dll] load: searching backend `sharp' in `/usr/lib/x86_64-linux-gnu/sane'
[dll] load: trying to load `/usr/lib/x86_64-linux-gnu/sane/libsane-sharp.so.1'
[dll] load: dlopen()ing `/usr/lib/x86_64-linux-gnu/sane/libsane-sharp.so.1'
[dll] init: initializing backend `sharp'
[dll] init: backend `sharp' is version 1.0.0
[dll] load: searching backend `sceptre' in `/usr/lib/x86_64-linux-gnu/sane'
[dll] load: trying to load `/usr/lib/x86_64-linux-gnu/sane/libsane-sceptre.so.1'
[dll] load: dlopen()ing `/usr/lib/x86_64-linux-gnu/sane/libsane-sceptre.so.1'
[dll] init: initializing backend `sceptre'
[dll] init: backend `sceptre' is version 1.0.10
[dll] load: searching backend `s9036' in `/usr/lib/x86_64-linux-gnu/sane'
[dll] load: trying to load `/usr/lib/x86_64-linux-gnu/sane/libsane-s9036.so.1'
[dll] load: dlopen()ing `/usr/lib/x86_64-linux-gnu/sane/libsane-s9036.so.1'
[dll] init: initializing backend `s9036'
[dll] init: backend `s9036' is version 1.0.0
[dll] load: searching backend `rts8891' in `/usr/lib/x86_64-linux-gnu/sane'
[dll] load: trying to load `/usr/lib/x86_64-linux-gnu/sane/libsane-rts8891.so.1'
[dll] load: dlopen()ing `/usr/lib/x86_64-linux-gnu/sane/libsane-rts8891.so.1'
[dll] init: initializing backend `rts8891'
[dll] init: backend `rts8891' is version 1.0.2401
[dll] load: searching backend `ricoh' in `/usr/lib/x86_64-linux-gnu/sane'
[dll] load: trying to load `/usr/lib/x86_64-linux-gnu/sane/libsane-ricoh.so.1'
[dll] load: dlopen()ing `/usr/lib/x86_64-linux-gnu/sane/libsane-ricoh.so.1'
[dll] init: initializing backend `ricoh'
[dll] init: backend `ricoh' is version 1.0.0
[dll] load: searching backend `qcam' in `/usr/lib/x86_64-linux-gnu/sane'
[dll] load: trying to load `/usr/lib/x86_64-linux-gnu/sane/libsane-qcam.so.1'
[dll] load: dlopen()ing `/usr/lib/x86_64-linux-gnu/sane/libsane-qcam.so.1'
[dll] init: initializing backend `qcam'
[dll] init: backend `qcam' is version 1.0.0
[dll] load: searching backend `plustek' in `/usr/lib/x86_64-linux-gnu/sane'
[dll] load: trying to load `/usr/lib/x86_64-linux-gnu/sane/libsane-plustek.so.1'
[dll] load: dlopen()ing `/usr/lib/x86_64-linux-gnu/sane/libsane-plustek.so.1'
[dll] init: initializing backend `plustek'
[dll] init: backend `plustek' is version 1.0.0
[dll] load: searching backend `pixma' in `/usr/lib/x86_64-linux-gnu/sane'
[dll] load: trying to load `/usr/lib/x86_64-linux-gnu/sane/libsane-pixma.so.1'
[dll] load: dlopen()ing `/usr/lib/x86_64-linux-gnu/sane/libsane-pixma.so.1'
[dll] init: initializing backend `pixma'
[dll] init: backend `pixma' is version 1.0.17
[dll] load: searching backend `pint' in `/usr/lib/x86_64-linux-gnu/sane'
[dll] load: trying to load `/usr/lib/x86_64-linux-gnu/sane/libsane-pint.so.1'
[dll] load: couldn't open `/usr/lib/x86_64-linux-gnu/sane/libsane-pint.so.1' (No such file or directory)
[dll] load: couldn't find backend `pint' (No such file or directory)
[dll] load: searching backend `pie' in `/usr/lib/x86_64-linux-gnu/sane'
[dll] load: trying to load `/usr/lib/x86_64-linux-gnu/sane/libsane-pie.so.1'
[dll] load: dlopen()ing `/usr/lib/x86_64-linux-gnu/sane/libsane-pie.so.1'
[dll] init: initializing backend `pie'
[dll] init: backend `pie' is version 1.0.9
[dll] load: searching backend `niash' in `/usr/lib/x86_64-linux-gnu/sane'
[dll] load: trying to load `/usr/lib/x86_64-linux-gnu/sane/libsane-niash.so.1'
[dll] load: dlopen()ing `/usr/lib/x86_64-linux-gnu/sane/libsane-niash.so.1'
[dll] init: initializing backend `niash'
[dll] init: backend `niash' is version 1.0.1
[dll] load: searching backend `nec' in `/usr/lib/x86_64-linux-gnu/sane'
[dll] load: trying to load `/usr/lib/x86_64-linux-gnu/sane/libsane-nec.so.1'
[dll] load: dlopen()ing `/usr/lib/x86_64-linux-gnu/sane/libsane-nec.so.1'
[dll] init: initializing backend `nec'
[dll] init: backend `nec' is version 1.0.0
[dll] load: searching backend `mustek_usb2' in `/usr/lib/x86_64-linux-gnu/sane'
[dll] load: trying to load `/usr/lib/x86_64-linux-gnu/sane/libsane-mustek_usb2.so.1'
[dll] load: dlopen()ing `/usr/lib/x86_64-linux-gnu/sane/libsane-mustek_usb2.so.1'
[dll] init: initializing backend `mustek_usb2'
[dll] init: backend `mustek_usb2' is version 1.0.10
[dll] load: searching backend `mustek_usb' in `/usr/lib/x86_64-linux-gnu/sane'
[dll] load: trying to load `/usr/lib/x86_64-linux-gnu/sane/libsane-mustek_usb.so.1'
[dll] load: dlopen()ing `/usr/lib/x86_64-linux-gnu/sane/libsane-mustek_usb.so.1'
[dll] init: initializing backend `mustek_usb'
[dll] init: backend `mustek_usb' is version 1.0.18
[dll] load: searching backend `mustek' in `/usr/lib/x86_64-linux-gnu/sane'
[dll] load: trying to load `/usr/lib/x86_64-linux-gnu/sane/libsane-mustek.so.1'
[dll] load: dlopen()ing `/usr/lib/x86_64-linux-gnu/sane/libsane-mustek.so.1'
[dll] init: initializing backend `mustek'
[dll] init: backend `mustek' is version 1.0.138
[dll] load: searching backend `microtek2' in `/usr/lib/x86_64-linux-gnu/sane'
[dll] load: trying to load `/usr/lib/x86_64-linux-gnu/sane/libsane-microtek2.so.1'
[dll] load: dlopen()ing `/usr/lib/x86_64-linux-gnu/sane/libsane-microtek2.so.1'
[dll] init: initializing backend `microtek2'
[dll] init: backend `microtek2' is version 1.0.0
[dll] load: searching backend `microtek' in `/usr/lib/x86_64-linux-gnu/sane'
[dll] load: trying to load `/usr/lib/x86_64-linux-gnu/sane/libsane-microtek.so.1'
[dll] load: dlopen()ing `/usr/lib/x86_64-linux-gnu/sane/libsane-microtek.so.1'
[dll] init: initializing backend `microtek'
[dll] init: backend `microtek' is version 1.0.0
[dll] load: searching backend `matsushita' in `/usr/lib/x86_64-linux-gnu/sane'
[dll] load: trying to load `/usr/lib/x86_64-linux-gnu/sane/libsane-matsushita.so.1'
[dll] load: dlopen()ing `/usr/lib/x86_64-linux-gnu/sane/libsane-matsushita.so.1'
[dll] init: initializing backend `matsushita'
[dll] init: backend `matsushita' is version 1.0.7
[dll] load: searching backend `magicolor' in `/usr/lib/x86_64-linux-gnu/sane'
[dll] load: trying to load `/usr/lib/x86_64-linux-gnu/sane/libsane-magicolor.so.1'
[dll] load: dlopen()ing `/usr/lib/x86_64-linux-gnu/sane/libsane-magicolor.so.1'
[dll] init: initializing backend `magicolor'
[dll] init: backend `magicolor' is version 1.0.1
[dll] load: searching backend `ma1509' in `/usr/lib/x86_64-linux-gnu/sane'
[dll] load: trying to load `/usr/lib/x86_64-linux-gnu/sane/libsane-ma1509.so.1'
[dll] load: dlopen()ing `/usr/lib/x86_64-linux-gnu/sane/libsane-ma1509.so.1'
[dll] init: initializing backend `ma1509'
[dll] init: backend `ma1509' is version 1.0.3
[dll] load: searching backend `lexmark' in `/usr/lib/x86_64-linux-gnu/sane'
[dll] load: trying to load `/usr/lib/x86_64-linux-gnu/sane/libsane-lexmark.so.1'
[dll] load: dlopen()ing `/usr/lib/x86_64-linux-gnu/sane/libsane-lexmark.so.1'
[dll] init: initializing backend `lexmark'
[dll] init: backend `lexmark' is version 1.0.32
[dll] load: searching backend `leo' in `/usr/lib/x86_64-linux-gnu/sane'
[dll] load: trying to load `/usr/lib/x86_64-linux-gnu/sane/libsane-leo.so.1'
[dll] load: dlopen()ing `/usr/lib/x86_64-linux-gnu/sane/libsane-leo.so.1'
[dll] init: initializing backend `leo'
[dll] init: backend `leo' is version 1.0.11
[dll] load: searching backend `kvs20xx' in `/usr/lib/x86_64-linux-gnu/sane'
[dll] load: trying to load `/usr/lib/x86_64-linux-gnu/sane/libsane-kvs20xx.so.1'
[dll] load: dlopen()ing `/usr/lib/x86_64-linux-gnu/sane/libsane-kvs20xx.so.1'
[dll] init: initializing backend `kvs20xx'
[dll] init: backend `kvs20xx' is version 1.0.2
[dll] load: searching backend `kvs1025' in `/usr/lib/x86_64-linux-gnu/sane'
[dll] load: trying to load `/usr/lib/x86_64-linux-gnu/sane/libsane-kvs1025.so.1'
[dll] load: dlopen()ing `/usr/lib/x86_64-linux-gnu/sane/libsane-kvs1025.so.1'
[dll] init: initializing backend `kvs1025'
[dll] init: backend `kvs1025' is version 1.0.5
[dll] load: searching backend `kodakaio' in `/usr/lib/x86_64-linux-gnu/sane'
[dll] load: trying to load `/usr/lib/x86_64-linux-gnu/sane/libsane-kodakaio.so.1'
[dll] load: dlopen()ing `/usr/lib/x86_64-linux-gnu/sane/libsane-kodakaio.so.1'
[dll] init: initializing backend `kodakaio'
[dll] init: backend `kodakaio' is version 1.0.3
[dll] load: searching backend `kodak' in `/usr/lib/x86_64-linux-gnu/sane'
[dll] load: trying to load `/usr/lib/x86_64-linux-gnu/sane/libsane-kodak.so.1'
[dll] load: dlopen()ing `/usr/lib/x86_64-linux-gnu/sane/libsane-kodak.so.1'
[dll] init: initializing backend `kodak'
[dll] init: backend `kodak' is version 1.0.7
[dll] load: searching backend `ibm' in `/usr/lib/x86_64-linux-gnu/sane'
[dll] load: trying to load `/usr/lib/x86_64-linux-gnu/sane/libsane-ibm.so.1'
[dll] load: dlopen()ing `/usr/lib/x86_64-linux-gnu/sane/libsane-ibm.so.1'
[dll] init: initializing backend `ibm'
[dll] init: backend `ibm' is version 1.0.0
[dll] load: searching backend `hs2p' in `/usr/lib/x86_64-linux-gnu/sane'
[dll] load: trying to load `/usr/lib/x86_64-linux-gnu/sane/libsane-hs2p.so.1'
[dll] load: dlopen()ing `/usr/lib/x86_64-linux-gnu/sane/libsane-hs2p.so.1'
[dll] init: initializing backend `hs2p'
[dll] init: backend `hs2p' is version 1.0.0
[dll] load: searching backend `hpljm1005' in `/usr/lib/x86_64-linux-gnu/sane'
[dll] load: trying to load `/usr/lib/x86_64-linux-gnu/sane/libsane-hpljm1005.so.1'
[dll] load: dlopen()ing `/usr/lib/x86_64-linux-gnu/sane/libsane-hpljm1005.so.1'
[dll] init: initializing backend `hpljm1005'
[dll] init: backend `hpljm1005' is version 1.0.1
[dll] load: searching backend `hp5590' in `/usr/lib/x86_64-linux-gnu/sane'
[dll] load: trying to load `/usr/lib/x86_64-linux-gnu/sane/libsane-hp5590.so.1'
[dll] load: dlopen()ing `/usr/lib/x86_64-linux-gnu/sane/libsane-hp5590.so.1'
[dll] init: initializing backend `hp5590'
[dll] init: backend `hp5590' is version 1.0.7
[dll] load: searching backend `hp5400' in `/usr/lib/x86_64-linux-gnu/sane'
[dll] load: trying to load `/usr/lib/x86_64-linux-gnu/sane/libsane-hp5400.so.1'
[dll] load: dlopen()ing `/usr/lib/x86_64-linux-gnu/sane/libsane-hp5400.so.1'
[dll] init: initializing backend `hp5400'
[dll] init: backend `hp5400' is version 1.0.3
[dll] load: searching backend `hp4200' in `/usr/lib/x86_64-linux-gnu/sane'
[dll] load: trying to load `/usr/lib/x86_64-linux-gnu/sane/libsane-hp4200.so.1'
[dll] load: dlopen()ing `/usr/lib/x86_64-linux-gnu/sane/libsane-hp4200.so.1'
[dll] init: initializing backend `hp4200'
[dll] init: backend `hp4200' is version 1.0.0
[dll] load: searching backend `hp3500' in `/usr/lib/x86_64-linux-gnu/sane'
[dll] load: trying to load `/usr/lib/x86_64-linux-gnu/sane/libsane-hp3500.so.1'
[dll] load: dlopen()ing `/usr/lib/x86_64-linux-gnu/sane/libsane-hp3500.so.1'
[dll] init: initializing backend `hp3500'
[dll] init: backend `hp3500' is version 1.0.0
[dll] load: searching backend `hpsj5s' in `/usr/lib/x86_64-linux-gnu/sane'
[dll] load: trying to load `/usr/lib/x86_64-linux-gnu/sane/libsane-hpsj5s.so.1'
[dll] load: dlopen()ing `/usr/lib/x86_64-linux-gnu/sane/libsane-hpsj5s.so.1'
[dll] init: initializing backend `hpsj5s'
[dll] init: backend `hpsj5s' is version 1.0.3
[dll] load: searching backend `hp3900' in `/usr/lib/x86_64-linux-gnu/sane'
[dll] load: trying to load `/usr/lib/x86_64-linux-gnu/sane/libsane-hp3900.so.1'
[dll] load: dlopen()ing `/usr/lib/x86_64-linux-gnu/sane/libsane-hp3900.so.1'
[dll] init: initializing backend `hp3900'
[dll] init: backend `hp3900' is version 1.0.0
[dll] load: searching backend `hp' in `/usr/lib/x86_64-linux-gnu/sane'
[dll] load: trying to load `/usr/lib/x86_64-linux-gnu/sane/libsane-hp.so.1'
[dll] load: dlopen()ing `/usr/lib/x86_64-linux-gnu/sane/libsane-hp.so.1'
[dll] init: initializing backend `hp'
[dll] init: backend `hp' is version 1.0.8
[dll] load: searching backend `gt68xx' in `/usr/lib/x86_64-linux-gnu/sane'
[dll] load: trying to load `/usr/lib/x86_64-linux-gnu/sane/libsane-gt68xx.so.1'
[dll] load: dlopen()ing `/usr/lib/x86_64-linux-gnu/sane/libsane-gt68xx.so.1'
[dll] init: initializing backend `gt68xx'
[dll] init: backend `gt68xx' is version 1.0.84
[dll] load: searching backend `genesys' in `/usr/lib/x86_64-linux-gnu/sane'
[dll] load: trying to load `/usr/lib/x86_64-linux-gnu/sane/libsane-genesys.so.1'
[dll] load: dlopen()ing `/usr/lib/x86_64-linux-gnu/sane/libsane-genesys.so.1'
[dll] init: initializing backend `genesys'
[dll] init: backend `genesys' is version 1.0.2511
[dll] load: searching backend `fujitsu' in `/usr/lib/x86_64-linux-gnu/sane'
[dll] load: trying to load `/usr/lib/x86_64-linux-gnu/sane/libsane-fujitsu.so.1'
[dll] load: dlopen()ing `/usr/lib/x86_64-linux-gnu/sane/libsane-fujitsu.so.1'
[dll] init: initializing backend `fujitsu'
[dll] init: backend `fujitsu' is version 1.0.133
[dll] load: searching backend `epsonds' in `/usr/lib/x86_64-linux-gnu/sane'
[dll] load: trying to load `/usr/lib/x86_64-linux-gnu/sane/libsane-epsonds.so.1'
[dll] load: dlopen()ing `/usr/lib/x86_64-linux-gnu/sane/libsane-epsonds.so.1'
[dll] init: initializing backend `epsonds'
[dll] init: backend `epsonds' is version 1.0.0
[dll] load: searching backend `epson2' in `/usr/lib/x86_64-linux-gnu/sane'
[dll] load: trying to load `/usr/lib/x86_64-linux-gnu/sane/libsane-epson2.so.1'
[dll] load: dlopen()ing `/usr/lib/x86_64-linux-gnu/sane/libsane-epson2.so.1'
[dll] init: initializing backend `epson2'
[dll] init: backend `epson2' is version 1.0.124
[dll] load: searching backend `epjitsu' in `/usr/lib/x86_64-linux-gnu/sane'
[dll] load: trying to load `/usr/lib/x86_64-linux-gnu/sane/libsane-epjitsu.so.1'
[dll] load: dlopen()ing `/usr/lib/x86_64-linux-gnu/sane/libsane-epjitsu.so.1'
[dll] init: initializing backend `epjitsu'
[dll] init: backend `epjitsu' is version 1.0.31
[dll] load: searching backend `dmc' in `/usr/lib/x86_64-linux-gnu/sane'
[dll] load: trying to load `/usr/lib/x86_64-linux-gnu/sane/libsane-dmc.so.1'
[dll] load: dlopen()ing `/usr/lib/x86_64-linux-gnu/sane/libsane-dmc.so.1'
[dll] init: initializing backend `dmc'
[dll] init: backend `dmc' is version 1.0.0
[dll] load: searching backend `dell1600n_net' in `/usr/lib/x86_64-linux-gnu/sane'
[dll] load: trying to load `/usr/lib/x86_64-linux-gnu/sane/libsane-dell1600n_net.so.1'
[dll] load: dlopen()ing `/usr/lib/x86_64-linux-gnu/sane/libsane-dell1600n_net.so.1'
[dll] init: initializing backend `dell1600n_net'
[dll] init: backend `dell1600n_net' is version 1.0.0
[dll] load: searching backend `coolscan3' in `/usr/lib/x86_64-linux-gnu/sane'
[dll] load: trying to load `/usr/lib/x86_64-linux-gnu/sane/libsane-coolscan3.so.1'
[dll] load: dlopen()ing `/usr/lib/x86_64-linux-gnu/sane/libsane-coolscan3.so.1'
[dll] init: initializing backend `coolscan3'
[dll] init: backend `coolscan3' is version 1.0.0
[dll] load: searching backend `coolscan' in `/usr/lib/x86_64-linux-gnu/sane'
[dll] load: trying to load `/usr/lib/x86_64-linux-gnu/sane/libsane-coolscan.so.1'
[dll] load: dlopen()ing `/usr/lib/x86_64-linux-gnu/sane/libsane-coolscan.so.1'
[dll] init: initializing backend `coolscan'
[dll] init: backend `coolscan' is version 1.0.0
[dll] load: searching backend `cardscan' in `/usr/lib/x86_64-linux-gnu/sane'
[dll] load: trying to load `/usr/lib/x86_64-linux-gnu/sane/libsane-cardscan.so.1'
[dll] load: dlopen()ing `/usr/lib/x86_64-linux-gnu/sane/libsane-cardscan.so.1'
[dll] init: initializing backend `cardscan'
[dll] init: backend `cardscan' is version 1.0.3
[dll] load: searching backend `canon_dr' in `/usr/lib/x86_64-linux-gnu/sane'
[dll] load: trying to load `/usr/lib/x86_64-linux-gnu/sane/libsane-canon_dr.so.1'
[dll] load: dlopen()ing `/usr/lib/x86_64-linux-gnu/sane/libsane-canon_dr.so.1'
[dll] init: initializing backend `canon_dr'
[dll] init: backend `canon_dr' is version 1.0.56
[dll] load: searching backend `canon630u' in `/usr/lib/x86_64-linux-gnu/sane'
[dll] load: trying to load `/usr/lib/x86_64-linux-gnu/sane/libsane-canon630u.so.1'
[dll] load: dlopen()ing `/usr/lib/x86_64-linux-gnu/sane/libsane-canon630u.so.1'
[dll] init: initializing backend `canon630u'
[dll] init: backend `canon630u' is version 1.0.1
[dll] load: searching backend `canon' in `/usr/lib/x86_64-linux-gnu/sane'
[dll] load: trying to load `/usr/lib/x86_64-linux-gnu/sane/libsane-canon.so.1'
[dll] load: dlopen()ing `/usr/lib/x86_64-linux-gnu/sane/libsane-canon.so.1'
[dll] init: initializing backend `canon'
[dll] init: backend `canon' is version 1.0.0
[dll] load: searching backend `bh' in `/usr/lib/x86_64-linux-gnu/sane'
[dll] load: trying to load `/usr/lib/x86_64-linux-gnu/sane/libsane-bh.so.1'
[dll] load: dlopen()ing `/usr/lib/x86_64-linux-gnu/sane/libsane-bh.so.1'
[dll] init: initializing backend `bh'
[dll] init: backend `bh' is version 1.0.4
[dll] load: searching backend `as6e' in `/usr/lib/x86_64-linux-gnu/sane'
[dll] load: trying to load `/usr/lib/x86_64-linux-gnu/sane/libsane-as6e.so.1'
[dll] load: dlopen()ing `/usr/lib/x86_64-linux-gnu/sane/libsane-as6e.so.1'
[dll] init: initializing backend `as6e'
[dll] load: searching backend `artec_eplus48u' in `/usr/lib/x86_64-linux-gnu/sane'
[dll] load: trying to load `/usr/lib/x86_64-linux-gnu/sane/libsane-artec_eplus48u.so.1'
[dll] load: dlopen()ing `/usr/lib/x86_64-linux-gnu/sane/libsane-artec_eplus48u.so.1'
[dll] init: initializing backend `artec_eplus48u'
[dll] init: backend `artec_eplus48u' is version 1.0.0
[dll] load: searching backend `artec' in `/usr/lib/x86_64-linux-gnu/sane'
[dll] load: trying to load `/usr/lib/x86_64-linux-gnu/sane/libsane-artec.so.1'
[dll] load: dlopen()ing `/usr/lib/x86_64-linux-gnu/sane/libsane-artec.so.1'
[dll] init: initializing backend `artec'
[dll] init: backend `artec' is version 1.0.0
[dll] load: searching backend `avision' in `/usr/lib/x86_64-linux-gnu/sane'
[dll] load: trying to load `/usr/lib/x86_64-linux-gnu/sane/libsane-avision.so.1'
[dll] load: dlopen()ing `/usr/lib/x86_64-linux-gnu/sane/libsane-avision.so.1'
[dll] init: initializing backend `avision'
[dll] init: backend `avision' is version 1.0.297
[dll] load: searching backend `apple' in `/usr/lib/x86_64-linux-gnu/sane'
[dll] load: trying to load `/usr/lib/x86_64-linux-gnu/sane/libsane-apple.so.1'
[dll] load: dlopen()ing `/usr/lib/x86_64-linux-gnu/sane/libsane-apple.so.1'
[dll] init: initializing backend `apple'
[dll] init: backend `apple' is version 1.0.0
[dll] load: searching backend `agfafocus' in `/usr/lib/x86_64-linux-gnu/sane'
[dll] load: trying to load `/usr/lib/x86_64-linux-gnu/sane/libsane-agfafocus.so.1'
[dll] load: dlopen()ing `/usr/lib/x86_64-linux-gnu/sane/libsane-agfafocus.so.1'
[dll] init: initializing backend `agfafocus'
[dll] init: backend `agfafocus' is version 1.0.0
[dll] load: searching backend `abaton' in `/usr/lib/x86_64-linux-gnu/sane'
[dll] load: trying to load `/usr/lib/x86_64-linux-gnu/sane/libsane-abaton.so.1'
[dll] load: dlopen()ing `/usr/lib/x86_64-linux-gnu/sane/libsane-abaton.so.1'
[dll] init: initializing backend `abaton'
[dll] init: backend `abaton' is version 1.0.0
[dll] load: searching backend `net' in `/usr/lib/x86_64-linux-gnu/sane'
[dll] load: trying to load `/usr/lib/x86_64-linux-gnu/sane/libsane-net.so.1'
[dll] load: dlopen()ing `/usr/lib/x86_64-linux-gnu/sane/libsane-net.so.1'
[dll] init: initializing backend `net'
[dll] init: backend `net' is version 1.0.27
[dll] load: searching backend `ls5000' in `/usr/lib/x86_64-linux-gnu/sane'
[dll] load: trying to load `/usr/lib/x86_64-linux-gnu/sane/libsane-ls5000.so.1'
[dll] load: dlopen()ing `/usr/lib/x86_64-linux-gnu/sane/libsane-ls5000.so.1'
[dll] init: initializing backend `ls5000'
[dll] init: backend `ls5000' is version 1.0.0
[dll] load: searching backend `hpaio' in `/usr/lib/x86_64-linux-gnu/sane'
[dll] load: trying to load `/usr/lib/x86_64-linux-gnu/sane/libsane-hpaio.so.1'
[dll] load: dlopen()ing `/usr/lib/x86_64-linux-gnu/sane/libsane-hpaio.so.1'
[dll] init: initializing backend `hpaio'
[dll] init: backend `hpaio' is version 1.0.0
[dll] sane_get_devices: found 0 devices
scanimage: no SANE devices found
[dll] sane_exit: exiting
[dll] sane_exit: calling backend `xerox_mfp's exit function
[dll] sane_exit: calling backend `umax1220u's exit function
[dll] sane_exit: calling backend `umax's exit function
[dll] sane_exit: calling backend `u12's exit function
[dll] sane_exit: calling backend `teco3's exit function
[dll] sane_exit: calling backend `teco2's exit function
[dll] sane_exit: calling backend `teco1's exit function
[dll] sane_exit: calling backend `tamarack's exit function
[dll] sane_exit: calling backend `sp15c's exit function
[dll] sane_exit: calling backend `snapscan's exit function
[dll] sane_exit: calling backend `sm3840's exit function
[dll] sane_exit: calling backend `sm3600's exit function
[dll] sane_exit: calling backend `sharp's exit function
[dll] sane_exit: calling backend `sceptre's exit function
[dll] sane_exit: calling backend `s9036's exit function
[dll] sane_exit: calling backend `rts8891's exit function
[dll] sane_exit: calling backend `ricoh's exit function
[dll] sane_exit: calling backend `qcam's exit function
[dll] sane_exit: calling backend `plustek's exit function
[dll] sane_exit: calling backend `pixma's exit function
[dll] sane_exit: calling backend `pie's exit function
[dll] sane_exit: calling backend `niash's exit function
[dll] sane_exit: calling backend `nec's exit function
[dll] sane_exit: calling backend `mustek_usb2's exit function
[dll] sane_exit: calling backend `mustek_usb's exit function
[dll] sane_exit: calling backend `mustek's exit function
[dll] sane_exit: calling backend `microtek2's exit function
[dll] sane_exit: calling backend `microtek's exit function
[dll] sane_exit: calling backend `matsushita's exit function
[dll] sane_exit: calling backend `magicolor's exit function
[dll] sane_exit: calling backend `ma1509's exit function
[dll] sane_exit: calling backend `lexmark's exit function
[dll] sane_exit: calling backend `leo's exit function
[dll] sane_exit: calling backend `kvs20xx's exit function
[dll] sane_exit: calling backend `kvs1025's exit function
[dll] sane_exit: calling backend `kodakaio's exit function
[dll] sane_exit: calling backend `kodak's exit function
[dll] sane_exit: calling backend `ibm's exit function
[dll] sane_exit: calling backend `hs2p's exit function
[dll] sane_exit: calling backend `hpljm1005's exit function
[dll] sane_exit: calling backend `hp5590's exit function
[dll] sane_exit: calling backend `hp5400's exit function
[dll] sane_exit: calling backend `hp4200's exit function
[dll] sane_exit: calling backend `hp3500's exit function
[dll] sane_exit: calling backend `hpsj5s's exit function
[dll] sane_exit: calling backend `hp3900's exit function
[dll] sane_exit: calling backend `hp's exit function
[dll] sane_exit: calling backend `gt68xx's exit function
[dll] sane_exit: calling backend `genesys's exit function
[dll] sane_exit: calling backend `fujitsu's exit function
[dll] sane_exit: calling backend `epsonds's exit function
[dll] sane_exit: calling backend `epson2's exit function
[dll] sane_exit: calling backend `epjitsu's exit function
[dll] sane_exit: calling backend `dmc's exit function
[dll] sane_exit: calling backend `dell1600n_net's exit function
[dll] sane_exit: calling backend `coolscan3's exit function
[dll] sane_exit: calling backend `coolscan's exit function
[dll] sane_exit: calling backend `cardscan's exit function
[dll] sane_exit: calling backend `canon_dr's exit function
[dll] sane_exit: calling backend `canon630u's exit function
[dll] sane_exit: calling backend `canon's exit function
[dll] sane_exit: calling backend `bh's exit function
[dll] sane_exit: calling backend `artec_eplus48u's exit function
[dll] sane_exit: calling backend `artec's exit function
[dll] sane_exit: calling backend `avision's exit function
[dll] sane_exit: calling backend `apple's exit function
[dll] sane_exit: calling backend `agfafocus's exit function
[dll] sane_exit: calling backend `abaton's exit function
[dll] sane_exit: calling backend `net's exit function
[dll] sane_exit: calling backend `ls5000's exit function
[dll] sane_exit: calling backend `hpaio's exit function
[dll] sane_exit: finished
Avatar utente
alle9
Scoppiettante Seguace
Scoppiettante Seguace
 
Messaggi: 937
Iscrizione: ottobre 2006
Località: macerata - Italy
Desktop: plasma
Distribuzione: Ubuntu 18.04 x86_64
Sesso: Maschile

Re: installazione scanner di rete Lexmark x464

Messaggioda magozurlinux » mercoledì 11 luglio 2018, 17:31

Dal debug ho trovato questi errori:

Codice: Seleziona tutto
[dll] load: couldn't open `/usr/lib/x86_64-linux-gnu/sane/libsane-lexmark_nscan.so.1' (No such file or directory)
[dll] load: couldn't find backend `lexmark_nscan' (No such file or directory)


da terminale postami questo comando:

Codice: Seleziona tutto
locate libsane-lexmark_nscan.so.1
XUBUNTU 16.04 LTS x86_64 Desktop :ciao:
Avatar utente
magozurlinux
Accecante Asceta
Accecante Asceta
 
Messaggi: 20098
Iscrizione: marzo 2010
Località: Pisa
Desktop: Desktop
Distribuzione: Xubuntu 16.04 LTS x86_64

Re: installazione scanner di rete Lexmark x464

Messaggioda alle9 » mercoledì 11 luglio 2018, 19:55

Codice: Seleziona tutto
alex@alex-LIFEBOOK-A512:~$ locate libsane-lexmark_nscan.so.1
/usr/lib64/sane/libsane-lexmark_nscan.so.1
/usr/lib64/sane/libsane-lexmark_nscan.so.1.0.16
/usr/local/lexmark/unix_scan_drivers/lib/sane/libsane-lexmark_nscan.so.1
/usr/local/lexmark/unix_scan_drivers/lib/sane/libsane-lexmark_nscan.so.1.0.16
Avatar utente
alle9
Scoppiettante Seguace
Scoppiettante Seguace
 
Messaggi: 937
Iscrizione: ottobre 2006
Località: macerata - Italy
Desktop: plasma
Distribuzione: Ubuntu 18.04 x86_64
Sesso: Maschile

Re: installazione scanner di rete Lexmark x464

Messaggioda magozurlinux » giovedì 12 luglio 2018, 12:16

Da terminale dai questo comando:

Codice: Seleziona tutto
sudo ln -s /usr/lib64/sane/libsane-lexmark_nscan.so* /usr/lib/x86_64-linux-gnu/sane/


prova lo scanner con la multifunzione Lexmark collegata alla porta usb..
XUBUNTU 16.04 LTS x86_64 Desktop :ciao:
Avatar utente
magozurlinux
Accecante Asceta
Accecante Asceta
 
Messaggi: 20098
Iscrizione: marzo 2010
Località: Pisa
Desktop: Desktop
Distribuzione: Xubuntu 16.04 LTS x86_64

Re: installazione scanner di rete Lexmark x464

Messaggioda alle9 » giovedì 12 luglio 2018, 15:28

prova lo scanner con la multifunzione Lexmark collegata alla porta usb..
ho provato a collegare la stampante con cavo usb e lanciare pc ubuntu Xsane image scanning program... ma niente da fare non vede lo scanner
poi ho ripetuto test precedente
Codice: Seleziona tutto
alex@alex-LIFEBOOK-A512:~$ scanimage --test
scanimage: no SANE devices found


andrebbe benissimo se come con windows riuscissi a far partire la scansione dal PC cliccando su icona. Ma richiede un programmino app di lexmark che per ubuntu mi sa che non esiste...
Avatar utente
alle9
Scoppiettante Seguace
Scoppiettante Seguace
 
Messaggi: 937
Iscrizione: ottobre 2006
Località: macerata - Italy
Desktop: plasma
Distribuzione: Ubuntu 18.04 x86_64
Sesso: Maschile

Re: installazione scanner di rete Lexmark x464

Messaggioda magozurlinux » giovedì 12 luglio 2018, 16:39

alle9 Immagine ha scritto:prova lo scanner con la multifunzione Lexmark collegata alla porta usb..
ho provato a collegare la stampante con cavo usb e lanciare pc ubuntu Xsane image scanning program... ma niente da fare non vede lo scanner
poi ho ripetuto test precedente
alex@alex-LIFEBOOK-A512:~$ scanimage --test
scanimage: no SANE devices found


andrebbe benissimo se come con windows riuscissi a far partire la scansione dal PC cliccando su icona. Ma richiede un programmino app di lexmark che per ubuntu mi sa che non esiste...


Prima di dare quel comando da terminale devi dare questo per il debug:

Codice: Seleziona tutto
export SANE_DEBUG_DLL=255


prima di farla funzionare in wifi bisogna farla funzionare collegata alla porta usb.
XUBUNTU 16.04 LTS x86_64 Desktop :ciao:
Avatar utente
magozurlinux
Accecante Asceta
Accecante Asceta
 
Messaggi: 20098
Iscrizione: marzo 2010
Località: Pisa
Desktop: Desktop
Distribuzione: Xubuntu 16.04 LTS x86_64

Re: installazione scanner di rete Lexmark x464

Messaggioda alle9 » giovedì 12 luglio 2018, 17:38

Codice: Seleziona tutto
alex@alex-LIFEBOOK-A512:~$ export SANE_DEBUG_DLL=255
alex@alex-LIFEBOOK-A512:~$ scanimage --test
[sanei_debug] Setting debug level of dll to 255.
[dll] sane_init: SANE dll backend version 1.0.13 from sane-backends 1.0.27
[dll] sane_init/read_dlld: attempting to open directory `./dll.d'
[dll] sane_init/read_dlld: attempting to open directory `/etc/sane.d/dll.d'
[dll] sane_init/read_dlld: using config directory `/etc/sane.d/dll.d'
[dll] sane_init/read_dlld: considering /etc/sane.d/dll.d/hplip
[dll] sane_init/read_config: reading dll.d/hplip
[dll] add_backend: adding backend `hpaio'
[dll] sane_init/read_dlld: considering /etc/sane.d/dll.d/libsane-extras
[dll] sane_init/read_config: reading dll.d/libsane-extras
[dll] add_backend: adding backend `ls5000'
[dll] sane_init/read_dlld: done.
[dll] sane_init/read_config: reading dll.conf
[dll] add_backend: adding backend `net'
[dll] add_backend: adding backend `abaton'
[dll] add_backend: adding backend `agfafocus'
[dll] add_backend: adding backend `apple'
[dll] add_backend: adding backend `avision'
[dll] add_backend: adding backend `artec'
[dll] add_backend: adding backend `artec_eplus48u'
[dll] add_backend: adding backend `as6e'
[dll] add_backend: adding backend `bh'
[dll] add_backend: adding backend `canon'
[dll] add_backend: adding backend `canon630u'
[dll] add_backend: adding backend `canon_dr'
[dll] add_backend: adding backend `cardscan'
[dll] add_backend: adding backend `coolscan'
[dll] add_backend: adding backend `coolscan3'
[dll] add_backend: adding backend `dell1600n_net'
[dll] add_backend: adding backend `dmc'
[dll] add_backend: adding backend `epjitsu'
[dll] add_backend: adding backend `epson2'
[dll] add_backend: adding backend `epsonds'
[dll] add_backend: adding backend `fujitsu'
[dll] add_backend: adding backend `genesys'
[dll] add_backend: adding backend `gt68xx'
[dll] add_backend: adding backend `hp'
[dll] add_backend: adding backend `hp3900'
[dll] add_backend: adding backend `hpsj5s'                                                                                                                                                     
[dll] add_backend: adding backend `hp3500'                                                                                                                                                     
[dll] add_backend: adding backend `hp4200'                                                                                                                                                     
[dll] add_backend: adding backend `hp5400'
[dll] add_backend: adding backend `hp5590'
[dll] add_backend: adding backend `hpljm1005'
[dll] add_backend: adding backend `hs2p'
[dll] add_backend: adding backend `ibm'
[dll] add_backend: adding backend `kodak'
[dll] add_backend: adding backend `kodakaio'
[dll] add_backend: adding backend `kvs1025'
[dll] add_backend: adding backend `kvs20xx'
[dll] add_backend: adding backend `leo'
[dll] add_backend: adding backend `lexmark'
[dll] add_backend: adding backend `ma1509'
[dll] add_backend: adding backend `magicolor'
[dll] add_backend: adding backend `matsushita'
[dll] add_backend: adding backend `microtek'
[dll] add_backend: adding backend `microtek2'
[dll] add_backend: adding backend `mustek'
[dll] add_backend: adding backend `mustek_usb'
[dll] add_backend: adding backend `mustek_usb2'
[dll] add_backend: adding backend `nec'
[dll] add_backend: adding backend `niash'
[dll] add_backend: adding backend `pie'
[dll] add_backend: adding backend `pint'
[dll] add_backend: adding backend `pixma'
[dll] add_backend: adding backend `plustek'
[dll] add_backend: adding backend `qcam'
[dll] add_backend: adding backend `ricoh'
[dll] add_backend: adding backend `rts8891'
[dll] add_backend: adding backend `s9036'
[dll] add_backend: adding backend `sceptre'
[dll] add_backend: adding backend `sharp'
[dll] add_backend: adding backend `sm3600'
[dll] add_backend: adding backend `sm3840'
[dll] add_backend: adding backend `snapscan'
[dll] add_backend: adding backend `sp15c'
[dll] add_backend: adding backend `tamarack'
[dll] add_backend: adding backend `teco1'
[dll] add_backend: adding backend `teco2'
[dll] add_backend: adding backend `teco3'
[dll] add_backend: adding backend `u12'
[dll] add_backend: adding backend `umax'
[dll] add_backend: adding backend `umax1220u'
[dll] add_backend: adding backend `v4l'
[dll] add_backend: adding backend `xerox_mfp'
[dll] add_backend: adding backend `lexmark_nscan'
[dll] sane_get_devices
[dll] load: searching backend `lexmark_nscan' in `/usr/lib/x86_64-linux-gnu/sane'
[dll] load: trying to load `/usr/lib/x86_64-linux-gnu/sane/libsane-lexmark_nscan.so.1'
[dll] load: dlopen()ing `/usr/lib/x86_64-linux-gnu/sane/libsane-lexmark_nscan.so.1'
[dll] load: dlopen() failed (libusb-0.1.so.4: cannot open shared object file: No such file or directory)
[dll] load: searching backend `xerox_mfp' in `/usr/lib/x86_64-linux-gnu/sane'
[dll] load: trying to load `/usr/lib/x86_64-linux-gnu/sane/libsane-xerox_mfp.so.1'
[dll] load: dlopen()ing `/usr/lib/x86_64-linux-gnu/sane/libsane-xerox_mfp.so.1'
[dll] init: initializing backend `xerox_mfp'
[dll] init: backend `xerox_mfp' is version 1.0.13
[dll] load: searching backend `v4l' in `/usr/lib/x86_64-linux-gnu/sane'
[dll] load: trying to load `/usr/lib/x86_64-linux-gnu/sane/libsane-v4l.so.1'
[dll] load: couldn't open `/usr/lib/x86_64-linux-gnu/sane/libsane-v4l.so.1' (No such file or directory)
[dll] load: couldn't find backend `v4l' (No such file or directory)
[dll] load: searching backend `umax1220u' in `/usr/lib/x86_64-linux-gnu/sane'
[dll] load: trying to load `/usr/lib/x86_64-linux-gnu/sane/libsane-umax1220u.so.1'
[dll] load: dlopen()ing `/usr/lib/x86_64-linux-gnu/sane/libsane-umax1220u.so.1'
[dll] init: initializing backend `umax1220u'
[dll] init: backend `umax1220u' is version 1.0.2
[dll] load: searching backend `umax' in `/usr/lib/x86_64-linux-gnu/sane'
[dll] load: trying to load `/usr/lib/x86_64-linux-gnu/sane/libsane-umax.so.1'
[dll] load: dlopen()ing `/usr/lib/x86_64-linux-gnu/sane/libsane-umax.so.1'
[dll] init: initializing backend `umax'
[dll] init: backend `umax' is version 1.0.45
[dll] load: searching backend `u12' in `/usr/lib/x86_64-linux-gnu/sane'
[dll] load: trying to load `/usr/lib/x86_64-linux-gnu/sane/libsane-u12.so.1'
[dll] load: dlopen()ing `/usr/lib/x86_64-linux-gnu/sane/libsane-u12.so.1'
[dll] init: initializing backend `u12'
[dll] init: backend `u12' is version 1.0.0
[dll] load: searching backend `teco3' in `/usr/lib/x86_64-linux-gnu/sane'
[dll] load: trying to load `/usr/lib/x86_64-linux-gnu/sane/libsane-teco3.so.1'
[dll] load: dlopen()ing `/usr/lib/x86_64-linux-gnu/sane/libsane-teco3.so.1'
[dll] init: initializing backend `teco3'
[dll] init: backend `teco3' is version 1.0.1
[dll] load: searching backend `teco2' in `/usr/lib/x86_64-linux-gnu/sane'
[dll] load: trying to load `/usr/lib/x86_64-linux-gnu/sane/libsane-teco2.so.1'
[dll] load: dlopen()ing `/usr/lib/x86_64-linux-gnu/sane/libsane-teco2.so.1'
[dll] init: initializing backend `teco2'
[dll] init: backend `teco2' is version 1.0.10
[dll] load: searching backend `teco1' in `/usr/lib/x86_64-linux-gnu/sane'
[dll] load: trying to load `/usr/lib/x86_64-linux-gnu/sane/libsane-teco1.so.1'
[dll] load: dlopen()ing `/usr/lib/x86_64-linux-gnu/sane/libsane-teco1.so.1'
[dll] init: initializing backend `teco1'
[dll] init: backend `teco1' is version 1.0.10
[dll] load: searching backend `tamarack' in `/usr/lib/x86_64-linux-gnu/sane'
[dll] load: trying to load `/usr/lib/x86_64-linux-gnu/sane/libsane-tamarack.so.1'
[dll] load: dlopen()ing `/usr/lib/x86_64-linux-gnu/sane/libsane-tamarack.so.1'
[dll] init: initializing backend `tamarack'
[dll] init: backend `tamarack' is version 1.0.0
[dll] load: searching backend `sp15c' in `/usr/lib/x86_64-linux-gnu/sane'
[dll] load: trying to load `/usr/lib/x86_64-linux-gnu/sane/libsane-sp15c.so.1'
[dll] load: dlopen()ing `/usr/lib/x86_64-linux-gnu/sane/libsane-sp15c.so.1'
[dll] init: initializing backend `sp15c'
[dll] init: backend `sp15c' is version 1.0.0
[dll] load: searching backend `snapscan' in `/usr/lib/x86_64-linux-gnu/sane'
[dll] load: trying to load `/usr/lib/x86_64-linux-gnu/sane/libsane-snapscan.so.1'
[dll] load: dlopen()ing `/usr/lib/x86_64-linux-gnu/sane/libsane-snapscan.so.1'
[dll] init: initializing backend `snapscan'
[dll] init: backend `snapscan' is version 1.4.53
[dll] load: searching backend `sm3840' in `/usr/lib/x86_64-linux-gnu/sane'
[dll] load: trying to load `/usr/lib/x86_64-linux-gnu/sane/libsane-sm3840.so.1'
[dll] load: dlopen()ing `/usr/lib/x86_64-linux-gnu/sane/libsane-sm3840.so.1'
[dll] init: initializing backend `sm3840'
[dll] init: backend `sm3840' is version 1.0.0
[dll] load: searching backend `sm3600' in `/usr/lib/x86_64-linux-gnu/sane'
[dll] load: trying to load `/usr/lib/x86_64-linux-gnu/sane/libsane-sm3600.so.1'
[dll] load: dlopen()ing `/usr/lib/x86_64-linux-gnu/sane/libsane-sm3600.so.1'
[dll] init: initializing backend `sm3600'
[dll] init: backend `sm3600' is version 1.0.6
[dll] load: searching backend `sharp' in `/usr/lib/x86_64-linux-gnu/sane'
[dll] load: trying to load `/usr/lib/x86_64-linux-gnu/sane/libsane-sharp.so.1'
[dll] load: dlopen()ing `/usr/lib/x86_64-linux-gnu/sane/libsane-sharp.so.1'
[dll] init: initializing backend `sharp'
[dll] init: backend `sharp' is version 1.0.0
[dll] load: searching backend `sceptre' in `/usr/lib/x86_64-linux-gnu/sane'
[dll] load: trying to load `/usr/lib/x86_64-linux-gnu/sane/libsane-sceptre.so.1'
[dll] load: dlopen()ing `/usr/lib/x86_64-linux-gnu/sane/libsane-sceptre.so.1'
[dll] init: initializing backend `sceptre'
[dll] init: backend `sceptre' is version 1.0.10
[dll] load: searching backend `s9036' in `/usr/lib/x86_64-linux-gnu/sane'
[dll] load: trying to load `/usr/lib/x86_64-linux-gnu/sane/libsane-s9036.so.1'
[dll] load: dlopen()ing `/usr/lib/x86_64-linux-gnu/sane/libsane-s9036.so.1'
[dll] init: initializing backend `s9036'
[dll] init: backend `s9036' is version 1.0.0
[dll] load: searching backend `rts8891' in `/usr/lib/x86_64-linux-gnu/sane'
[dll] load: trying to load `/usr/lib/x86_64-linux-gnu/sane/libsane-rts8891.so.1'
[dll] load: dlopen()ing `/usr/lib/x86_64-linux-gnu/sane/libsane-rts8891.so.1'
[dll] init: initializing backend `rts8891'
[dll] init: backend `rts8891' is version 1.0.2401
[dll] load: searching backend `ricoh' in `/usr/lib/x86_64-linux-gnu/sane'
[dll] load: trying to load `/usr/lib/x86_64-linux-gnu/sane/libsane-ricoh.so.1'
[dll] load: dlopen()ing `/usr/lib/x86_64-linux-gnu/sane/libsane-ricoh.so.1'
[dll] init: initializing backend `ricoh'
[dll] init: backend `ricoh' is version 1.0.0
[dll] load: searching backend `qcam' in `/usr/lib/x86_64-linux-gnu/sane'
[dll] load: trying to load `/usr/lib/x86_64-linux-gnu/sane/libsane-qcam.so.1'
[dll] load: dlopen()ing `/usr/lib/x86_64-linux-gnu/sane/libsane-qcam.so.1'
[dll] init: initializing backend `qcam'
[dll] init: backend `qcam' is version 1.0.0
[dll] load: searching backend `plustek' in `/usr/lib/x86_64-linux-gnu/sane'
[dll] load: trying to load `/usr/lib/x86_64-linux-gnu/sane/libsane-plustek.so.1'
[dll] load: dlopen()ing `/usr/lib/x86_64-linux-gnu/sane/libsane-plustek.so.1'
[dll] init: initializing backend `plustek'
[dll] init: backend `plustek' is version 1.0.0
[dll] load: searching backend `pixma' in `/usr/lib/x86_64-linux-gnu/sane'
[dll] load: trying to load `/usr/lib/x86_64-linux-gnu/sane/libsane-pixma.so.1'
[dll] load: dlopen()ing `/usr/lib/x86_64-linux-gnu/sane/libsane-pixma.so.1'
[dll] init: initializing backend `pixma'
[dll] init: backend `pixma' is version 1.0.17
[dll] load: searching backend `pint' in `/usr/lib/x86_64-linux-gnu/sane'
[dll] load: trying to load `/usr/lib/x86_64-linux-gnu/sane/libsane-pint.so.1'
[dll] load: couldn't open `/usr/lib/x86_64-linux-gnu/sane/libsane-pint.so.1' (No such file or directory)
[dll] load: couldn't find backend `pint' (No such file or directory)
[dll] load: searching backend `pie' in `/usr/lib/x86_64-linux-gnu/sane'
[dll] load: trying to load `/usr/lib/x86_64-linux-gnu/sane/libsane-pie.so.1'
[dll] load: dlopen()ing `/usr/lib/x86_64-linux-gnu/sane/libsane-pie.so.1'
[dll] init: initializing backend `pie'
[dll] init: backend `pie' is version 1.0.9
[dll] load: searching backend `niash' in `/usr/lib/x86_64-linux-gnu/sane'
[dll] load: trying to load `/usr/lib/x86_64-linux-gnu/sane/libsane-niash.so.1'
[dll] load: dlopen()ing `/usr/lib/x86_64-linux-gnu/sane/libsane-niash.so.1'
[dll] init: initializing backend `niash'
[dll] init: backend `niash' is version 1.0.1
[dll] load: searching backend `nec' in `/usr/lib/x86_64-linux-gnu/sane'
[dll] load: trying to load `/usr/lib/x86_64-linux-gnu/sane/libsane-nec.so.1'
[dll] load: dlopen()ing `/usr/lib/x86_64-linux-gnu/sane/libsane-nec.so.1'
[dll] init: initializing backend `nec'
[dll] init: backend `nec' is version 1.0.0
[dll] load: searching backend `mustek_usb2' in `/usr/lib/x86_64-linux-gnu/sane'
[dll] load: trying to load `/usr/lib/x86_64-linux-gnu/sane/libsane-mustek_usb2.so.1'
[dll] load: dlopen()ing `/usr/lib/x86_64-linux-gnu/sane/libsane-mustek_usb2.so.1'
[dll] init: initializing backend `mustek_usb2'
[dll] init: backend `mustek_usb2' is version 1.0.10
[dll] load: searching backend `mustek_usb' in `/usr/lib/x86_64-linux-gnu/sane'
[dll] load: trying to load `/usr/lib/x86_64-linux-gnu/sane/libsane-mustek_usb.so.1'
[dll] load: dlopen()ing `/usr/lib/x86_64-linux-gnu/sane/libsane-mustek_usb.so.1'
[dll] init: initializing backend `mustek_usb'
[dll] init: backend `mustek_usb' is version 1.0.18
[dll] load: searching backend `mustek' in `/usr/lib/x86_64-linux-gnu/sane'
[dll] load: trying to load `/usr/lib/x86_64-linux-gnu/sane/libsane-mustek.so.1'
[dll] load: dlopen()ing `/usr/lib/x86_64-linux-gnu/sane/libsane-mustek.so.1'
[dll] init: initializing backend `mustek'
[dll] init: backend `mustek' is version 1.0.138
[dll] load: searching backend `microtek2' in `/usr/lib/x86_64-linux-gnu/sane'
[dll] load: trying to load `/usr/lib/x86_64-linux-gnu/sane/libsane-microtek2.so.1'
[dll] load: dlopen()ing `/usr/lib/x86_64-linux-gnu/sane/libsane-microtek2.so.1'
[dll] init: initializing backend `microtek2'
[dll] init: backend `microtek2' is version 1.0.0
[dll] load: searching backend `microtek' in `/usr/lib/x86_64-linux-gnu/sane'
[dll] load: trying to load `/usr/lib/x86_64-linux-gnu/sane/libsane-microtek.so.1'
[dll] load: dlopen()ing `/usr/lib/x86_64-linux-gnu/sane/libsane-microtek.so.1'
[dll] init: initializing backend `microtek'
[dll] init: backend `microtek' is version 1.0.0
[dll] load: searching backend `matsushita' in `/usr/lib/x86_64-linux-gnu/sane'
[dll] load: trying to load `/usr/lib/x86_64-linux-gnu/sane/libsane-matsushita.so.1'
[dll] load: dlopen()ing `/usr/lib/x86_64-linux-gnu/sane/libsane-matsushita.so.1'
[dll] init: initializing backend `matsushita'
[dll] init: backend `matsushita' is version 1.0.7
[dll] load: searching backend `magicolor' in `/usr/lib/x86_64-linux-gnu/sane'
[dll] load: trying to load `/usr/lib/x86_64-linux-gnu/sane/libsane-magicolor.so.1'
[dll] load: dlopen()ing `/usr/lib/x86_64-linux-gnu/sane/libsane-magicolor.so.1'
[dll] init: initializing backend `magicolor'
[dll] init: backend `magicolor' is version 1.0.1
[dll] load: searching backend `ma1509' in `/usr/lib/x86_64-linux-gnu/sane'
[dll] load: trying to load `/usr/lib/x86_64-linux-gnu/sane/libsane-ma1509.so.1'
[dll] load: dlopen()ing `/usr/lib/x86_64-linux-gnu/sane/libsane-ma1509.so.1'
[dll] init: initializing backend `ma1509'
[dll] init: backend `ma1509' is version 1.0.3
[dll] load: searching backend `lexmark' in `/usr/lib/x86_64-linux-gnu/sane'
[dll] load: trying to load `/usr/lib/x86_64-linux-gnu/sane/libsane-lexmark.so.1'
[dll] load: dlopen()ing `/usr/lib/x86_64-linux-gnu/sane/libsane-lexmark.so.1'
[dll] init: initializing backend `lexmark'
[dll] init: backend `lexmark' is version 1.0.32
[dll] load: searching backend `leo' in `/usr/lib/x86_64-linux-gnu/sane'
[dll] load: trying to load `/usr/lib/x86_64-linux-gnu/sane/libsane-leo.so.1'
[dll] load: dlopen()ing `/usr/lib/x86_64-linux-gnu/sane/libsane-leo.so.1'
[dll] init: initializing backend `leo'
[dll] init: backend `leo' is version 1.0.11
[dll] load: searching backend `kvs20xx' in `/usr/lib/x86_64-linux-gnu/sane'
[dll] load: trying to load `/usr/lib/x86_64-linux-gnu/sane/libsane-kvs20xx.so.1'
[dll] load: dlopen()ing `/usr/lib/x86_64-linux-gnu/sane/libsane-kvs20xx.so.1'
[dll] init: initializing backend `kvs20xx'
[dll] init: backend `kvs20xx' is version 1.0.2
[dll] load: searching backend `kvs1025' in `/usr/lib/x86_64-linux-gnu/sane'
[dll] load: trying to load `/usr/lib/x86_64-linux-gnu/sane/libsane-kvs1025.so.1'
[dll] load: dlopen()ing `/usr/lib/x86_64-linux-gnu/sane/libsane-kvs1025.so.1'
[dll] init: initializing backend `kvs1025'
[dll] init: backend `kvs1025' is version 1.0.5
[dll] load: searching backend `kodakaio' in `/usr/lib/x86_64-linux-gnu/sane'
[dll] load: trying to load `/usr/lib/x86_64-linux-gnu/sane/libsane-kodakaio.so.1'
[dll] load: dlopen()ing `/usr/lib/x86_64-linux-gnu/sane/libsane-kodakaio.so.1'
[dll] init: initializing backend `kodakaio'
[dll] init: backend `kodakaio' is version 1.0.3
[dll] load: searching backend `kodak' in `/usr/lib/x86_64-linux-gnu/sane'
[dll] load: trying to load `/usr/lib/x86_64-linux-gnu/sane/libsane-kodak.so.1'
[dll] load: dlopen()ing `/usr/lib/x86_64-linux-gnu/sane/libsane-kodak.so.1'
[dll] init: initializing backend `kodak'
[dll] init: backend `kodak' is version 1.0.7
[dll] load: searching backend `ibm' in `/usr/lib/x86_64-linux-gnu/sane'
[dll] load: trying to load `/usr/lib/x86_64-linux-gnu/sane/libsane-ibm.so.1'
[dll] load: dlopen()ing `/usr/lib/x86_64-linux-gnu/sane/libsane-ibm.so.1'
[dll] init: initializing backend `ibm'
[dll] init: backend `ibm' is version 1.0.0
[dll] load: searching backend `hs2p' in `/usr/lib/x86_64-linux-gnu/sane'
[dll] load: trying to load `/usr/lib/x86_64-linux-gnu/sane/libsane-hs2p.so.1'
[dll] load: dlopen()ing `/usr/lib/x86_64-linux-gnu/sane/libsane-hs2p.so.1'
[dll] init: initializing backend `hs2p'
[dll] init: backend `hs2p' is version 1.0.0
[dll] load: searching backend `hpljm1005' in `/usr/lib/x86_64-linux-gnu/sane'
[dll] load: trying to load `/usr/lib/x86_64-linux-gnu/sane/libsane-hpljm1005.so.1'
[dll] load: dlopen()ing `/usr/lib/x86_64-linux-gnu/sane/libsane-hpljm1005.so.1'
[dll] init: initializing backend `hpljm1005'
[dll] init: backend `hpljm1005' is version 1.0.1
[dll] load: searching backend `hp5590' in `/usr/lib/x86_64-linux-gnu/sane'
[dll] load: trying to load `/usr/lib/x86_64-linux-gnu/sane/libsane-hp5590.so.1'
[dll] load: dlopen()ing `/usr/lib/x86_64-linux-gnu/sane/libsane-hp5590.so.1'
[dll] init: initializing backend `hp5590'
[dll] init: backend `hp5590' is version 1.0.7
[dll] load: searching backend `hp5400' in `/usr/lib/x86_64-linux-gnu/sane'
[dll] load: trying to load `/usr/lib/x86_64-linux-gnu/sane/libsane-hp5400.so.1'
[dll] load: dlopen()ing `/usr/lib/x86_64-linux-gnu/sane/libsane-hp5400.so.1'
[dll] init: initializing backend `hp5400'
[dll] init: backend `hp5400' is version 1.0.3
[dll] load: searching backend `hp4200' in `/usr/lib/x86_64-linux-gnu/sane'
[dll] load: trying to load `/usr/lib/x86_64-linux-gnu/sane/libsane-hp4200.so.1'
[dll] load: dlopen()ing `/usr/lib/x86_64-linux-gnu/sane/libsane-hp4200.so.1'
[dll] init: initializing backend `hp4200'
[dll] init: backend `hp4200' is version 1.0.0
[dll] load: searching backend `hp3500' in `/usr/lib/x86_64-linux-gnu/sane'
[dll] load: trying to load `/usr/lib/x86_64-linux-gnu/sane/libsane-hp3500.so.1'
[dll] load: dlopen()ing `/usr/lib/x86_64-linux-gnu/sane/libsane-hp3500.so.1'
[dll] init: initializing backend `hp3500'
[dll] init: backend `hp3500' is version 1.0.0
[dll] load: searching backend `hpsj5s' in `/usr/lib/x86_64-linux-gnu/sane'
[dll] load: trying to load `/usr/lib/x86_64-linux-gnu/sane/libsane-hpsj5s.so.1'
[dll] load: dlopen()ing `/usr/lib/x86_64-linux-gnu/sane/libsane-hpsj5s.so.1'
[dll] init: initializing backend `hpsj5s'
[dll] init: backend `hpsj5s' is version 1.0.3
[dll] load: searching backend `hp3900' in `/usr/lib/x86_64-linux-gnu/sane'
[dll] load: trying to load `/usr/lib/x86_64-linux-gnu/sane/libsane-hp3900.so.1'
[dll] load: dlopen()ing `/usr/lib/x86_64-linux-gnu/sane/libsane-hp3900.so.1'
[dll] init: initializing backend `hp3900'
[dll] init: backend `hp3900' is version 1.0.0
[dll] load: searching backend `hp' in `/usr/lib/x86_64-linux-gnu/sane'
[dll] load: trying to load `/usr/lib/x86_64-linux-gnu/sane/libsane-hp.so.1'
[dll] load: dlopen()ing `/usr/lib/x86_64-linux-gnu/sane/libsane-hp.so.1'
[dll] init: initializing backend `hp'
[dll] init: backend `hp' is version 1.0.8
[dll] load: searching backend `gt68xx' in `/usr/lib/x86_64-linux-gnu/sane'
[dll] load: trying to load `/usr/lib/x86_64-linux-gnu/sane/libsane-gt68xx.so.1'
[dll] load: dlopen()ing `/usr/lib/x86_64-linux-gnu/sane/libsane-gt68xx.so.1'
[dll] init: initializing backend `gt68xx'
[dll] init: backend `gt68xx' is version 1.0.84
[dll] load: searching backend `genesys' in `/usr/lib/x86_64-linux-gnu/sane'
[dll] load: trying to load `/usr/lib/x86_64-linux-gnu/sane/libsane-genesys.so.1'
[dll] load: dlopen()ing `/usr/lib/x86_64-linux-gnu/sane/libsane-genesys.so.1'
[dll] init: initializing backend `genesys'
[dll] init: backend `genesys' is version 1.0.2511
[dll] load: searching backend `fujitsu' in `/usr/lib/x86_64-linux-gnu/sane'
[dll] load: trying to load `/usr/lib/x86_64-linux-gnu/sane/libsane-fujitsu.so.1'
[dll] load: dlopen()ing `/usr/lib/x86_64-linux-gnu/sane/libsane-fujitsu.so.1'
[dll] init: initializing backend `fujitsu'
[dll] init: backend `fujitsu' is version 1.0.133
[dll] load: searching backend `epsonds' in `/usr/lib/x86_64-linux-gnu/sane'
[dll] load: trying to load `/usr/lib/x86_64-linux-gnu/sane/libsane-epsonds.so.1'
[dll] load: dlopen()ing `/usr/lib/x86_64-linux-gnu/sane/libsane-epsonds.so.1'
[dll] init: initializing backend `epsonds'
[dll] init: backend `epsonds' is version 1.0.0
[dll] load: searching backend `epson2' in `/usr/lib/x86_64-linux-gnu/sane'
[dll] load: trying to load `/usr/lib/x86_64-linux-gnu/sane/libsane-epson2.so.1'
[dll] load: dlopen()ing `/usr/lib/x86_64-linux-gnu/sane/libsane-epson2.so.1'
[dll] init: initializing backend `epson2'
[dll] init: backend `epson2' is version 1.0.124
[dll] load: searching backend `epjitsu' in `/usr/lib/x86_64-linux-gnu/sane'
[dll] load: trying to load `/usr/lib/x86_64-linux-gnu/sane/libsane-epjitsu.so.1'
[dll] load: dlopen()ing `/usr/lib/x86_64-linux-gnu/sane/libsane-epjitsu.so.1'
[dll] init: initializing backend `epjitsu'
[dll] init: backend `epjitsu' is version 1.0.31
[dll] load: searching backend `dmc' in `/usr/lib/x86_64-linux-gnu/sane'
[dll] load: trying to load `/usr/lib/x86_64-linux-gnu/sane/libsane-dmc.so.1'
[dll] load: dlopen()ing `/usr/lib/x86_64-linux-gnu/sane/libsane-dmc.so.1'
[dll] init: initializing backend `dmc'
[dll] init: backend `dmc' is version 1.0.0
[dll] load: searching backend `dell1600n_net' in `/usr/lib/x86_64-linux-gnu/sane'
[dll] load: trying to load `/usr/lib/x86_64-linux-gnu/sane/libsane-dell1600n_net.so.1'
[dll] load: dlopen()ing `/usr/lib/x86_64-linux-gnu/sane/libsane-dell1600n_net.so.1'
[dll] init: initializing backend `dell1600n_net'
[dll] init: backend `dell1600n_net' is version 1.0.0
[dll] load: searching backend `coolscan3' in `/usr/lib/x86_64-linux-gnu/sane'
[dll] load: trying to load `/usr/lib/x86_64-linux-gnu/sane/libsane-coolscan3.so.1'
[dll] load: dlopen()ing `/usr/lib/x86_64-linux-gnu/sane/libsane-coolscan3.so.1'
[dll] init: initializing backend `coolscan3'
[dll] init: backend `coolscan3' is version 1.0.0
[dll] load: searching backend `coolscan' in `/usr/lib/x86_64-linux-gnu/sane'
[dll] load: trying to load `/usr/lib/x86_64-linux-gnu/sane/libsane-coolscan.so.1'
[dll] load: dlopen()ing `/usr/lib/x86_64-linux-gnu/sane/libsane-coolscan.so.1'
[dll] init: initializing backend `coolscan'
[dll] init: backend `coolscan' is version 1.0.0
[dll] load: searching backend `cardscan' in `/usr/lib/x86_64-linux-gnu/sane'
[dll] load: trying to load `/usr/lib/x86_64-linux-gnu/sane/libsane-cardscan.so.1'
[dll] load: dlopen()ing `/usr/lib/x86_64-linux-gnu/sane/libsane-cardscan.so.1'
[dll] init: initializing backend `cardscan'
[dll] init: backend `cardscan' is version 1.0.3
[dll] load: searching backend `canon_dr' in `/usr/lib/x86_64-linux-gnu/sane'
[dll] load: trying to load `/usr/lib/x86_64-linux-gnu/sane/libsane-canon_dr.so.1'
[dll] load: dlopen()ing `/usr/lib/x86_64-linux-gnu/sane/libsane-canon_dr.so.1'
[dll] init: initializing backend `canon_dr'
[dll] init: backend `canon_dr' is version 1.0.56
[dll] load: searching backend `canon630u' in `/usr/lib/x86_64-linux-gnu/sane'
[dll] load: trying to load `/usr/lib/x86_64-linux-gnu/sane/libsane-canon630u.so.1'
[dll] load: dlopen()ing `/usr/lib/x86_64-linux-gnu/sane/libsane-canon630u.so.1'
[dll] init: initializing backend `canon630u'
[dll] init: backend `canon630u' is version 1.0.1
[dll] load: searching backend `canon' in `/usr/lib/x86_64-linux-gnu/sane'
[dll] load: trying to load `/usr/lib/x86_64-linux-gnu/sane/libsane-canon.so.1'
[dll] load: dlopen()ing `/usr/lib/x86_64-linux-gnu/sane/libsane-canon.so.1'
[dll] init: initializing backend `canon'
[dll] init: backend `canon' is version 1.0.0
[dll] load: searching backend `bh' in `/usr/lib/x86_64-linux-gnu/sane'
[dll] load: trying to load `/usr/lib/x86_64-linux-gnu/sane/libsane-bh.so.1'
[dll] load: dlopen()ing `/usr/lib/x86_64-linux-gnu/sane/libsane-bh.so.1'
[dll] init: initializing backend `bh'
[dll] init: backend `bh' is version 1.0.4
[dll] load: searching backend `as6e' in `/usr/lib/x86_64-linux-gnu/sane'
[dll] load: trying to load `/usr/lib/x86_64-linux-gnu/sane/libsane-as6e.so.1'
[dll] load: dlopen()ing `/usr/lib/x86_64-linux-gnu/sane/libsane-as6e.so.1'
[dll] init: initializing backend `as6e'
[dll] load: searching backend `artec_eplus48u' in `/usr/lib/x86_64-linux-gnu/sane'
[dll] load: trying to load `/usr/lib/x86_64-linux-gnu/sane/libsane-artec_eplus48u.so.1'
[dll] load: dlopen()ing `/usr/lib/x86_64-linux-gnu/sane/libsane-artec_eplus48u.so.1'
[dll] init: initializing backend `artec_eplus48u'
[dll] init: backend `artec_eplus48u' is version 1.0.0
[dll] load: searching backend `artec' in `/usr/lib/x86_64-linux-gnu/sane'
[dll] load: trying to load `/usr/lib/x86_64-linux-gnu/sane/libsane-artec.so.1'
[dll] load: dlopen()ing `/usr/lib/x86_64-linux-gnu/sane/libsane-artec.so.1'
[dll] init: initializing backend `artec'
[dll] init: backend `artec' is version 1.0.0
[dll] load: searching backend `avision' in `/usr/lib/x86_64-linux-gnu/sane'
[dll] load: trying to load `/usr/lib/x86_64-linux-gnu/sane/libsane-avision.so.1'
[dll] load: dlopen()ing `/usr/lib/x86_64-linux-gnu/sane/libsane-avision.so.1'
[dll] init: initializing backend `avision'
[dll] init: backend `avision' is version 1.0.297
[dll] load: searching backend `apple' in `/usr/lib/x86_64-linux-gnu/sane'
[dll] load: trying to load `/usr/lib/x86_64-linux-gnu/sane/libsane-apple.so.1'
[dll] load: dlopen()ing `/usr/lib/x86_64-linux-gnu/sane/libsane-apple.so.1'
[dll] init: initializing backend `apple'
[dll] init: backend `apple' is version 1.0.0
[dll] load: searching backend `agfafocus' in `/usr/lib/x86_64-linux-gnu/sane'
[dll] load: trying to load `/usr/lib/x86_64-linux-gnu/sane/libsane-agfafocus.so.1'
[dll] load: dlopen()ing `/usr/lib/x86_64-linux-gnu/sane/libsane-agfafocus.so.1'
[dll] init: initializing backend `agfafocus'
[dll] init: backend `agfafocus' is version 1.0.0
[dll] load: searching backend `abaton' in `/usr/lib/x86_64-linux-gnu/sane'
[dll] load: trying to load `/usr/lib/x86_64-linux-gnu/sane/libsane-abaton.so.1'
[dll] load: dlopen()ing `/usr/lib/x86_64-linux-gnu/sane/libsane-abaton.so.1'
[dll] init: initializing backend `abaton'
[dll] init: backend `abaton' is version 1.0.0
[dll] load: searching backend `net' in `/usr/lib/x86_64-linux-gnu/sane'
[dll] load: trying to load `/usr/lib/x86_64-linux-gnu/sane/libsane-net.so.1'
[dll] load: dlopen()ing `/usr/lib/x86_64-linux-gnu/sane/libsane-net.so.1'
[dll] init: initializing backend `net'
[dll] init: backend `net' is version 1.0.27
[dll] load: searching backend `ls5000' in `/usr/lib/x86_64-linux-gnu/sane'
[dll] load: trying to load `/usr/lib/x86_64-linux-gnu/sane/libsane-ls5000.so.1'
[dll] load: dlopen()ing `/usr/lib/x86_64-linux-gnu/sane/libsane-ls5000.so.1'
[dll] init: initializing backend `ls5000'
[dll] init: backend `ls5000' is version 1.0.0
[dll] load: searching backend `hpaio' in `/usr/lib/x86_64-linux-gnu/sane'
[dll] load: trying to load `/usr/lib/x86_64-linux-gnu/sane/libsane-hpaio.so.1'
[dll] load: dlopen()ing `/usr/lib/x86_64-linux-gnu/sane/libsane-hpaio.so.1'
[dll] init: initializing backend `hpaio'
[dll] init: backend `hpaio' is version 1.0.0
[dll] sane_get_devices: found 0 devices
scanimage: no SANE devices found
[dll] sane_exit: exiting
[dll] sane_exit: calling backend `xerox_mfp's exit function
[dll] sane_exit: calling backend `umax1220u's exit function
[dll] sane_exit: calling backend `umax's exit function
[dll] sane_exit: calling backend `u12's exit function
[dll] sane_exit: calling backend `teco3's exit function
[dll] sane_exit: calling backend `teco2's exit function
[dll] sane_exit: calling backend `teco1's exit function
[dll] sane_exit: calling backend `tamarack's exit function
[dll] sane_exit: calling backend `sp15c's exit function
[dll] sane_exit: calling backend `snapscan's exit function
[dll] sane_exit: calling backend `sm3840's exit function
[dll] sane_exit: calling backend `sm3600's exit function
[dll] sane_exit: calling backend `sharp's exit function
[dll] sane_exit: calling backend `sceptre's exit function
[dll] sane_exit: calling backend `s9036's exit function
[dll] sane_exit: calling backend `rts8891's exit function
[dll] sane_exit: calling backend `ricoh's exit function
[dll] sane_exit: calling backend `qcam's exit function
[dll] sane_exit: calling backend `plustek's exit function
[dll] sane_exit: calling backend `pixma's exit function
[dll] sane_exit: calling backend `pie's exit function
[dll] sane_exit: calling backend `niash's exit function
[dll] sane_exit: calling backend `nec's exit function
[dll] sane_exit: calling backend `mustek_usb2's exit function
[dll] sane_exit: calling backend `mustek_usb's exit function
[dll] sane_exit: calling backend `mustek's exit function
[dll] sane_exit: calling backend `microtek2's exit function
[dll] sane_exit: calling backend `microtek's exit function
[dll] sane_exit: calling backend `matsushita's exit function
[dll] sane_exit: calling backend `magicolor's exit function
[dll] sane_exit: calling backend `ma1509's exit function
[dll] sane_exit: calling backend `lexmark's exit function
[dll] sane_exit: calling backend `leo's exit function
[dll] sane_exit: calling backend `kvs20xx's exit function
[dll] sane_exit: calling backend `kvs1025's exit function
[dll] sane_exit: calling backend `kodakaio's exit function
[dll] sane_exit: calling backend `kodak's exit function
[dll] sane_exit: calling backend `ibm's exit function
[dll] sane_exit: calling backend `hs2p's exit function
[dll] sane_exit: calling backend `hpljm1005's exit function
[dll] sane_exit: calling backend `hp5590's exit function
[dll] sane_exit: calling backend `hp5400's exit function
[dll] sane_exit: calling backend `hp4200's exit function
[dll] sane_exit: calling backend `hp3500's exit function
[dll] sane_exit: calling backend `hpsj5s's exit function
[dll] sane_exit: calling backend `hp3900's exit function
[dll] sane_exit: calling backend `hp's exit function
[dll] sane_exit: calling backend `gt68xx's exit function
[dll] sane_exit: calling backend `genesys's exit function
[dll] sane_exit: calling backend `fujitsu's exit function
[dll] sane_exit: calling backend `epsonds's exit function
[dll] sane_exit: calling backend `epson2's exit function
[dll] sane_exit: calling backend `epjitsu's exit function
[dll] sane_exit: calling backend `dmc's exit function
[dll] sane_exit: calling backend `dell1600n_net's exit function
[dll] sane_exit: calling backend `coolscan3's exit function
[dll] sane_exit: calling backend `coolscan's exit function
[dll] sane_exit: calling backend `cardscan's exit function
[dll] sane_exit: calling backend `canon_dr's exit function
[dll] sane_exit: calling backend `canon630u's exit function
[dll] sane_exit: calling backend `canon's exit function
[dll] sane_exit: calling backend `bh's exit function
[dll] sane_exit: calling backend `artec_eplus48u's exit function
[dll] sane_exit: calling backend `artec's exit function
[dll] sane_exit: calling backend `avision's exit function
[dll] sane_exit: calling backend `apple's exit function
[dll] sane_exit: calling backend `agfafocus's exit function
[dll] sane_exit: calling backend `abaton's exit function
[dll] sane_exit: calling backend `net's exit function
[dll] sane_exit: calling backend `ls5000's exit function
[dll] sane_exit: calling backend `hpaio's exit function
[dll] sane_exit: finished
Avatar utente
alle9
Scoppiettante Seguace
Scoppiettante Seguace
 
Messaggi: 937
Iscrizione: ottobre 2006
Località: macerata - Italy
Desktop: plasma
Distribuzione: Ubuntu 18.04 x86_64
Sesso: Maschile

Re: installazione scanner di rete Lexmark x464

Messaggioda alle9 » venerdì 13 luglio 2018, 13:04

niente da fare collegato con usb lanciando xsane imaging scanning program non lo vede
Avatar utente
alle9
Scoppiettante Seguace
Scoppiettante Seguace
 
Messaggi: 937
Iscrizione: ottobre 2006
Località: macerata - Italy
Desktop: plasma
Distribuzione: Ubuntu 18.04 x86_64
Sesso: Maschile

Re: installazione scanner di rete Lexmark x464

Messaggioda alle9 » venerdì 13 luglio 2018, 18:41

Riprovo ad eseguire dall'inizio i controlli fatti per vedere se abbiamo dimenticato qualcosa

Codice: Seleziona tutto
alex@alex-LIFEBOOK-A512:~$ lsusb
Bus 002 Device 004: ID 8087:07da Intel Corp.
Bus 002 Device 003: ID 1d57:5a66 Xenta
Bus 002 Device 005: ID 043d:0169 Lexmark International, Inc.
Bus 002 Device 002: ID 8087:0024 Intel Corp. Integrated Rate Matching Hub
Bus 002 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
Bus 001 Device 004: ID 04f2:b302 Chicony Electronics Co., Ltd
Bus 001 Device 002: ID 8087:0024 Intel Corp. Integrated Rate Matching Hub
Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub


Codice: Seleziona tutto
alex@alex-LIFEBOOK-A512:~$ sudo scanimage -L

No scanners were identified. If you were expecting something different,
check that the scanner is plugged in, turned on and detected by the
sane-find-scanner tool (if appropriate). Please read the documentation
which came with this software (README, FAQ, manpages).


Codice: Seleziona tutto
alex@alex-LIFEBOOK-A512:~$ sudo sane-find-scanner

  # sane-find-scanner will now attempt to detect your scanner. If the
  # result is different from what you expected, first make sure your
  # scanner is powered up and properly connected to your computer.

  # No SCSI scanners found. If you expected something different, make sure that
  # you have loaded a kernel SCSI driver for your SCSI adapter.

found USB scanner (vendor=0x043d [Lexmark International], product=0x0169 [Lexmark X464de]) at libusb:002:005
  # Your USB scanner was (probably) detected. It may or may not be supported by                                                                                                                 
  # SANE. Try scanimage -L and read the backend's manpage.                                                                                                                                     
                                                                                                                                                                                               
  # Not checking for parallel port scanners.

  # Most Scanners connected to the parallel port or other proprietary ports
  # can't be detected by this program.


Codice: Seleziona tutto
alex@alex-LIFEBOOK-A512:~$ groups
alex adm cdrom sudo dip plugdev lpadmin scanner saned sambashare


Codice: Seleziona tutto
alex@alex-LIFEBOOK-A512:~$ grep 043d -n3 /lib/udev/rules.d/60-libsane1.rules
29-
30-LABEL="libsane_scsi_rules_begin"
31-# Lexmark X464
32:ATTRS{idVendor}=="043d", ATTRS{idProduct}=="0169", MODE="664", GROUP="scanner", ENV{libsane_matched}="yes"
33-KERNEL!="sg[0-9]*", GOTO="libsane_rules_end"
34-
35-# Generic: SCSI device type 6 indicates a scanner
alex@alex-LIFEBOOK-A512:~$


contenuto sudo -H gedit /lib/udev/rules.d/60-libsane1.rules
Codice: Seleziona tutto
# This file was automatically created based on description files (*.desc)
#
# udev rules file for supported USB and SCSI devices
#
# For the list of supported USB devices see /usr/lib/udev/hwdb.d/20-sane.hwdb
#
# The SCSI device support is very basic and includes only
# scanners that mark themselves as type "scanner" or
# SCSI-scanners from HP and other vendors that are entitled "processor"
# but are treated accordingly.
#
# If your SCSI scanner isn't listed below, you can add it to a new rules
# file under /etc/udev/rules.d/.
#
# If your scanner is supported by some external backend (brother, epkowa,
# hpaio, etc) please ask the author of the backend to provide proper
# device detection support for your OS
#
# If the scanner is supported by sane-backends, please mail the entry to
# the sane-devel mailing list (sane-devel@lists.alioth.debian.org).
#
ACTION!="add", GOTO="libsane_rules_end"

# The following rule will disable USB autosuspend for the device
ENV{DEVTYPE}=="usb_device", ENV{libsane_matched}=="yes", TEST=="power/control", ATTR{power/control}="on"

SUBSYSTEMS=="scsi", GOTO="libsane_scsi_rules_begin"
GOTO="libsane_rules_end"

LABEL="libsane_scsi_rules_begin"
# Lexmark X464
ATTRS{idVendor}=="043d", ATTRS{idProduct}=="0169", MODE="664", GROUP="scanner", ENV{libsane_matched}="yes"
KERNEL!="sg[0-9]*", GOTO="libsane_rules_end"

# Generic: SCSI device type 6 indicates a scanner
ATTRS{type}=="6", ENV{libsane_matched}="yes"

# Some scanners advertise themselves as SCSI device type 3

# Wildcard: for some Epson SCSI scanners
ATTRS{type}=="3", ATTRS{vendor}=="EPSON", ATTRS{model}=="SCANNER*", ENV{libsane_matched}="yes"

# Epson Expression 800 | Epson Expression 800
ATTRS{type}=="3", ATTRS{vendor}=="EPSON", ATTRS{model}=="Expression800", ENV{libsane_matched}="yes"

# Epson Perfection 2450 | Epson GT-9700F | Epson Perfection 2450 PHOTO
ATTRS{type}=="3", ATTRS{vendor}=="EPSON", ATTRS{model}=="GT-9700", ENV{libsane_matched}="yes"

# Epson Perfection 3200 | Epson GT-9800F | Epson Perfection 3200 PHOTO
ATTRS{type}=="3", ATTRS{vendor}=="EPSON", ATTRS{model}=="GT-9800", ENV{libsane_matched}="yes"

# Epson GT-X900 | Epson Perfection V700 Photo | Epson Perfection V750 Photo
ATTRS{type}=="3", ATTRS{vendor}=="EPSON", ATTRS{model}=="GT-X900", ENV{libsane_matched}="yes"

# Epson Perfection 636S | Epson Perfection 1200S | Epson Perfection 1200S
ATTRS{type}=="3", ATTRS{vendor}=="EPSON", ATTRS{model}=="Perfection1200", ENV{libsane_matched}="yes"

# Epson Perfection 636 | Epson Perfection 636S
ATTRS{type}=="3", ATTRS{vendor}=="EPSON", ATTRS{model}=="Perfection636", ENV{libsane_matched}="yes"

# Hewlett-Packard ScanJet 4p
ATTRS{type}=="3", ATTRS{vendor}=="HP", ATTRS{model}=="C1130A", ENV{libsane_matched}="yes"

# Hewlett-Packard ScanJet IIc
ATTRS{type}=="3", ATTRS{vendor}=="HP", ATTRS{model}=="C1750A", ENV{libsane_matched}="yes"

# Hewlett-Packard ScanJet IIp
ATTRS{type}=="3", ATTRS{vendor}=="HP", ATTRS{model}=="C1790A", ENV{libsane_matched}="yes"

# Hewlett-Packard ScanJet IIcx
ATTRS{type}=="3", ATTRS{vendor}=="HP", ATTRS{model}=="C2500A", ENV{libsane_matched}="yes"

# Hewlett-Packard ScanJet 4c
ATTRS{type}=="3", ATTRS{vendor}=="HP", ATTRS{model}=="C2520A", ENV{libsane_matched}="yes"

# Hewlett-Packard ScanJet 5p
ATTRS{type}=="3", ATTRS{vendor}=="HP", ATTRS{model}=="C5110A", ENV{libsane_matched}="yes"

# Hewlett-Packard ScanJet 6200C
ATTRS{type}=="3", ATTRS{vendor}=="HP", ATTRS{model}=="C6270A", ENV{libsane_matched}="yes"

# Hewlett-Packard ScanJet 6300C
ATTRS{type}=="3", ATTRS{vendor}=="HP", ATTRS{model}=="C7670A", ENV{libsane_matched}="yes"


LABEL="libsane_rules_end"
Avatar utente
alle9
Scoppiettante Seguace
Scoppiettante Seguace
 
Messaggi: 937
Iscrizione: ottobre 2006
Località: macerata - Italy
Desktop: plasma
Distribuzione: Ubuntu 18.04 x86_64
Sesso: Maschile

Re: installazione scanner di rete Lexmark x464

Messaggioda alle9 » sabato 14 luglio 2018, 16:06

desumo che non funziona e che non c'è nulla da fare???
Avatar utente
alle9
Scoppiettante Seguace
Scoppiettante Seguace
 
Messaggi: 937
Iscrizione: ottobre 2006
Località: macerata - Italy
Desktop: plasma
Distribuzione: Ubuntu 18.04 x86_64
Sesso: Maschile

Re: installazione scanner di rete Lexmark x464

Messaggioda alle9 » lunedì 16 luglio 2018, 11:40

ho installato anche:
lexmark_network-scan-linux-glibc2_06082017_x86_64.deb

ma niente da fare
Avatar utente
alle9
Scoppiettante Seguace
Scoppiettante Seguace
 
Messaggi: 937
Iscrizione: ottobre 2006
Località: macerata - Italy
Desktop: plasma
Distribuzione: Ubuntu 18.04 x86_64
Sesso: Maschile

Re: installazione scanner di rete Lexmark x464

Messaggioda magozurlinux » lunedì 16 luglio 2018, 12:01

Ciao.

Non trovo soluzioni per farti funzionare lo scanner.
XUBUNTU 16.04 LTS x86_64 Desktop :ciao:
Avatar utente
magozurlinux
Accecante Asceta
Accecante Asceta
 
Messaggi: 20098
Iscrizione: marzo 2010
Località: Pisa
Desktop: Desktop
Distribuzione: Xubuntu 16.04 LTS x86_64

Re: installazione scanner di rete Lexmark x464

Messaggioda alle9 » lunedì 16 luglio 2018, 23:12

immaginavo io ho scritto al servizio supporto lexmark e neanche loro mi hanno risposto... mi sa che non funzia Grazie, lascio aperto e speriamo che qualcuno che ha la stessa stampante ci sappia dare la dritta se c'è
grazie mille
Avatar utente
alle9
Scoppiettante Seguace
Scoppiettante Seguace
 
Messaggi: 937
Iscrizione: ottobre 2006
Località: macerata - Italy
Desktop: plasma
Distribuzione: Ubuntu 18.04 x86_64
Sesso: Maschile

Precedente

Torna a Driver e periferiche

Chi c’è in linea

Visualizzano questa sezione: 0 utenti registrati e 24 ospiti