HP 2630 riconosciuta solo se accesa al boot?

[corradoventu]

La mia multifunzione HP 2630 viene riconosciuta solo se accesa e collegata al boot?
Se quando accendo il PC non è accesa e collegata (via USB) non viene riconosciuta(?) e non funziona ne come stampante ne come scanner.
Su Ubuntu 20.04 e 20.10 NON viene riconosciuta neanche se accesa, per farla funzionare devo eseguire hp-doctor, su 21.04 non serve hp-doctor ma deve essere pre-collegata.
Ma l'USB non dovrebbe ovviare a problemi del genere?
Non chiedo aiuto per ovviare al problema (non mi costa nulla tenerla collegata o eseguire hp-doctor) ma vorrei sapere se capita qualcosa di simile anche a voi.
Grazie

[Roberto Pontecorvi]

hp-doctor)

perchè non posti il risultato, così vediamo cosa installa il comando. Penso che tu lo abbia già fatto, di hplip è uscita 3.20.11 che pare funzioni alla grande su quelle distribuzioni.

[magozurlinux]

Ciao.

Posta anche questo comando:

Codice: Seleziona tutto

dmesg | grep usb

[corradoventu]

Questo da Ubuntu 21.04 dove tutto funziona, stampante accesa prima del boot

Codice: Seleziona tutto

corrado@corrado-x5-hh-1207:~$ sudo dmesg | grep usb
[sudo] password for corrado: 
[    0.165107] usbcore: registered new interface driver usbfs
[    0.165107] usbcore: registered new interface driver hub
[    0.165107] usbcore: registered new device driver usb
[    0.582610] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 5.08
[    0.582611] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    0.582612] usb usb1: Product: xHCI Host Controller
[    0.582613] usb usb1: Manufacturer: Linux 5.8.0-25-generic xhci-hcd
[    0.582614] usb usb1: SerialNumber: 0000:00:14.0
[    0.583943] usb usb2: New USB device found, idVendor=1d6b, idProduct=0003, bcdDevice= 5.08
[    0.583944] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    0.583945] usb usb2: Product: xHCI Host Controller
[    0.583946] usb usb2: Manufacturer: Linux 5.8.0-25-generic xhci-hcd
[    0.583946] usb usb2: SerialNumber: 0000:00:14.0
[    0.588513] usb usb3: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 5.08
[    0.588514] usb usb3: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    0.588515] usb usb3: Product: xHCI Host Controller
[    0.588516] usb usb3: Manufacturer: Linux 5.8.0-25-generic xhci-hcd
[    0.588517] usb usb3: SerialNumber: 0000:01:00.0
[    0.588756] usb usb4: New USB device found, idVendor=1d6b, idProduct=0003, bcdDevice= 5.08
[    0.588760] usb usb4: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    0.588761] usb usb4: Product: xHCI Host Controller
[    0.588762] usb usb4: Manufacturer: Linux 5.8.0-25-generic xhci-hcd
[    0.588762] usb usb4: SerialNumber: 0000:01:00.0
[    0.921070] usb 1-1: new low-speed USB device number 2 using xhci_hcd
[    0.921073] usb 3-1: new high-speed USB device number 2 using xhci_hcd
[    1.074203] usb 1-1: New USB device found, idVendor=1bcf, idProduct=0007, bcdDevice= 0.14
[    1.074209] usb 1-1: New USB device strings: Mfr=0, Product=2, SerialNumber=0
[    1.074214] usb 1-1: Product: USB Optical Mouse
[    1.074997] usb 3-1: New USB device found, idVendor=2109, idProduct=3431, bcdDevice= 4.20
[    1.075001] usb 3-1: New USB device strings: Mfr=0, Product=1, SerialNumber=0
[    1.075004] usb 3-1: Product: USB2.0 Hub
[    1.205019] usb 1-2: new high-speed USB device number 3 using xhci_hcd
[    1.484022] usb 1-2: New USB device found, idVendor=046d, idProduct=0990, bcdDevice= 0.07
[    1.484027] usb 1-2: New USB device strings: Mfr=0, Product=0, SerialNumber=2
[    1.484030] usb 1-2: SerialNumber: 54BF41F0
[    1.613021] usb 1-4: new full-speed USB device number 4 using xhci_hcd
[    1.785426] usb 1-4: New USB device found, idVendor=145f, idProduct=02b5, bcdDevice= 0.02
[    1.785430] usb 1-4: New USB device strings: Mfr=1, Product=2, SerialNumber=0
[    1.785434] usb 1-4: Product: Trust Wireless Mouse
[    1.785436] usb 1-4: Manufacturer: YICHIP
[    1.913035] usb 1-6: new high-speed USB device number 5 using xhci_hcd
[    2.062818] usb 1-6: New USB device found, idVendor=058f, idProduct=6377, bcdDevice= 1.00
[    2.062823] usb 1-6: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[    2.062826] usb 1-6: Product: Mass Storage Device
[    2.062829] usb 1-6: Manufacturer: Generic
[    2.062831] usb 1-6: SerialNumber: 920321111113
[    2.189066] usb 1-8: new high-speed USB device number 6 using xhci_hcd
[    2.363286] usb 1-8: New USB device found, idVendor=05a3, idProduct=9530, bcdDevice= 1.00
[    2.363291] usb 1-8: New USB device strings: Mfr=2, Product=1, SerialNumber=3
[    2.363294] usb 1-8: Product: USB 2.0 Camera
[    2.363296] usb 1-8: Manufacturer: Sonix Technology Co., Ltd.
[    2.363299] usb 1-8: SerialNumber: SN0256
[    2.493077] usb 1-10: new high-speed USB device number 7 using xhci_hcd
[    2.641789] usb 1-10: New USB device found, idVendor=03f0, idProduct=0053, bcdDevice= 1.00
[    2.641794] usb 1-10: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[    2.641797] usb 1-10: Product: DeskJet 2600 series
[    2.641800] usb 1-10: Manufacturer: HP
[    2.641802] usb 1-10: SerialNumber: CN0569B27006PS
[    2.653512] usb-storage 1-6:1.0: USB Mass Storage device detected
[    2.653618] scsi host4: usb-storage 1-6:1.0
[    2.653683] usbcore: registered new interface driver usb-storage
[    2.654967] usbcore: registered new interface driver uas
[    2.677519] usbcore: registered new interface driver usbhid
[    2.677520] usbhid: USB HID core driver
[    2.679633] input: USB Optical Mouse as /devices/pci0000:00/0000:00:14.0/usb1/1-1/1-1:1.0/0003:1BCF:0007.0001/input/input4
[    2.679753] input: USB Optical Mouse as /devices/pci0000:00/0000:00:14.0/usb1/1-1/1-1:1.0/0003:1BCF:0007.0001/input/input5
[    2.679855] hid-generic 0003:1BCF:0007.0001: input,hiddev0,hidraw0: USB HID v1.10 Mouse [USB Optical Mouse] on usb-0000:00:14.0-1/input0
[    2.680190] hid-generic 0003:145F:02B5.0002: hiddev1,hidraw1: USB HID v2.00 Device [YICHIP Trust Wireless Mouse] on usb-0000:00:14.0-4/input0
[    2.680479] input: YICHIP Trust Wireless Mouse as /devices/pci0000:00/0000:00:14.0/usb1/1-4/1-4:1.1/0003:145F:02B5.0003/input/input6
[    2.680567] input: YICHIP Trust Wireless Mouse System Control as /devices/pci0000:00/0000:00:14.0/usb1/1-4/1-4:1.1/0003:145F:02B5.0003/input/input7
[    2.737367] input: YICHIP Trust Wireless Mouse Consumer Control as /devices/pci0000:00/0000:00:14.0/usb1/1-4/1-4:1.1/0003:145F:02B5.0003/input/input8
[    2.737794] hid-generic 0003:145F:02B5.0003: input,hiddev2,hidraw2: USB HID v2.00 Mouse [YICHIP Trust Wireless Mouse] on usb-0000:00:14.0-4/input1
[    3.811061] input: UVC Camera (046d:0990) as /devices/pci0000:00/0000:00:14.0/usb1/1-2/1-2:1.0/input/input10
[    3.834990] input: USB 2.0 Camera: HD USB Camera as /devices/pci0000:00/0000:00:14.0/usb1/1-8/1-8:1.0/input/input12
[    3.835048] usbcore: registered new interface driver uvcvideo
[    4.409261] usb 1-2: Warning! Unlikely big volume range (=3072), cval->res is probably wrong.
[    4.409263] usb 1-2: [5] FU [Mic Capture Volume] ch = 1, val = 4608/7680/1
[    4.409414] usbcore: registered new interface driver snd-usb-audio
[    4.465407] usblp 1-10:1.1: usblp3: USB Bidirectional printer dev 7 if 1 alt 0 proto 2 vid 0x03F0 pid 0x0053
[    4.465437] usbcore: registered new interface driver usblp
[    7.631604] usblp3: removed
[    8.561193] usb 1-2: reset high-speed USB device number 3 using xhci_hcd
corrado@corrado-x5-hh-1207:~$ lsusb
Bus 002 Device 001: ID 1d6b:0003 Linux Foundation 3.0 root hub
Bus 001 Device 006: ID 05a3:9530 ARC International USB 2.0 Camera
Bus 001 Device 005: ID 058f:6377 Alcor Micro Corp. AU6375 4-LUN card reader
Bus 001 Device 004: ID 145f:02b5 Trust Trust Wireless Mouse
Bus 001 Device 003: ID 046d:0990 Logitech, Inc. QuickCam Pro 9000
Bus 001 Device 007: ID 03f0:0053 HP, Inc DeskJet 2620 All-in-One Printer
Bus 001 Device 002: ID 1bcf:0007 Sunplus Innovation Technology Inc. Optical Mouse
Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
Bus 004 Device 001: ID 1d6b:0003 Linux Foundation 3.0 root hub
Bus 003 Device 002: ID 2109:3431 VIA Labs, Inc. Hub
Bus 003 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
corrado@corrado-x5-hh-1207:~$ 

[magozurlinux]

Da terminale dai questi comandi:

Codice: Seleziona tutto

sudo -H gedit /etc/udev/rules.d/10-usbprinter.rules

copia e incolla questa riga:

Codice: Seleziona tutto

ATTR{idVendor}=="03f0", ATTR{idProduct}=="0053", MODE:="0660", GROUP:="lp"

salva ed esci dall'editor

Codice: Seleziona tutto

sudo service udev restart

Codice: Seleziona tutto

sudo adduser corrado lp

Codice: Seleziona tutto

echo usblp | sudo tee -a /etc/modules

chiudi il terminale e riavvia il pc.

Prova la stampante accesa anche dopo il boot.

[corradoventu]

Codice: Seleziona tutto

corrado@corrado-x5-hh-1207:~$ sudo service udev restart
corrado@corrado-x5-hh-1207:~$ sudo adduser corrado lp
Adding user `corrado' to group `lp' ...
Adding user corrado to group lp
Done.
corrado@corrado-x5-hh-1207:~$ echo usblp | sudo tee -a /etc/modules
usblp
corrado@corrado-x5-hh-1207:~$

Edit: Ubuntu 21.04 Fatto boot con stampante collegata ma spenta, poi accesa
MAGNIFICO! funziona! sei un MAGO! (nomen omen)
Per la stampante ne vedo 2, la prima non va, la seconda SI.
Lo scanner ha funzionato solo DOPO aver stampato una pagina, prima non vedeva lo scanner.
GRAZIE!

RiEdit: domani farò qualche prova con il 20.04 e il 20.10

RiRiedit: sul 20.04 non funzionava neanche se la printer era accesae collegata al boot, dopo la tua cura FUNZIONA. Lo scanner (simple-scan) trova lo scanner giusto e funziona dopo aver stampato una pagina, ma non prima.
grazie ancora!

Riedit ancora altrimenti mi cazziano per doppio post: sul 21.04 è arrivato il nuovo hplip

Codice: Seleziona tutto

corrado@corrado-x6-hh-1214:~$ apt policy hplip
hplip:
  Installed: 3.20.11+dfsg0-1
  Candidate: 3.20.11+dfsg0-1
  Version table:
 *** 3.20.11+dfsg0-1 500
        500 http://archive.ubuntu.com/ubuntu hirsute/main amd64 Packages
        100 /var/lib/dpkg/status
corrado@corrado-x6-hh-1214:~$ 

così per prova ho installato la nuova ISO: Ubuntu 21.04 "Hirsute Hippo" - Alpha amd64 (20201213)
e ho provato la stampante e lo scanner SENZA le modifiche del MAGO
FUNZIONA TUTTO OOTB (Out Of The Box) anche se la stampante non è collegata a Boot