[RISOLTO][Wireless] wireless con avm fritz

[maitarco]

...e mi viene:
sudo wpa_supplicant -D wext -i wlan0 -c /etc/wpa_supplicant.conf -dd
Initializing interface 'wlan0' conf '/etc/wpa_supplicant.conf' driver 'wext' ctrl_interface 'N/A' bridge 'N/A'
Configuration file '/etc/wpa_supplicant.conf' -> '/etc/wpa_supplicant.conf'
Reading configuration file '/etc/wpa_supplicant.conf'
ctrl_interface='/var/run/wpa_supplicant'
ctrl_interface_group='1000' (DEPRECATED)
update_config=1
Line: 5 - start of a new network block
ssid - hexdump_ascii(len=9):
    61 6d 69 63 6f 66 72 69 74                        amicofrit     
key_mgmt: 0x2
proto: 0x1
pairwise: 0x8
group: 0x8
PSK (ASCII passphrase) - hexdump_ascii(len=16): [REMOVED]
PSK (from passphrase) - hexdump(len=32): [REMOVED]
Priority group 0
  id=0 ssid='amicofrit'
Initializing interface (2) 'wlan0'
EAPOL: SUPP_PAE entering state DISCONNECTED
EAPOL: KEY_RX entering state NO_KEY_RECEIVE
EAPOL: SUPP_BE entering state INITIALIZE
EAP: EAP entering state DISABLED
EAPOL: External notification - portEnabled=0
EAPOL: External notification - portValid=0
SIOCGIWRANGE: WE(compiled)=21 WE(source)=9 enc_capa=0xf
  capabilities: key_mgmt 0xf enc 0xf
WEXT: Operstate: linkmode=1, operstate=5
Own MAC address: 00:04:0e:ff:2e:dc
wpa_driver_wext_set_wpa
wpa_driver_wext_set_key: alg=0 key_idx=0 set_tx=0 seq_len=0 key_len=0
wpa_driver_wext_set_key: alg=0 key_idx=1 set_tx=0 seq_len=0 key_len=0
wpa_driver_wext_set_key: alg=0 key_idx=2 set_tx=0 seq_len=0 key_len=0
wpa_driver_wext_set_key: alg=0 key_idx=3 set_tx=0 seq_len=0 key_len=0
wpa_driver_wext_set_countermeasures
wpa_driver_wext_set_drop_unencrypted
Setting scan request: 0 sec 100000 usec
ctrl_interface_group=1000
Added interface wlan0
RTM_NEWLINK: operstate=0 ifi_flags=0x1002 ()
Wireless event: cmd=0x8b06 len=8
RTM_NEWLINK: operstate=0 ifi_flags=0x11043 ([UP][RUNNING][LOWER_UP])
RTM_NEWLINK, IFLA_IFNAME: Interface 'wlan0' added
RTM_NEWLINK: operstate=0 ifi_flags=0x11043 ([UP][RUNNING][LOWER_UP])
RTM_NEWLINK, IFLA_IFNAME: Interface 'wlan0' added
RTM_NEWLINK: operstate=0 ifi_flags=0x11003 ([UP][LOWER_UP])
RTM_NEWLINK, IFLA_IFNAME: Interface 'wlan0' added
State: DISCONNECTED -> SCANNING
Starting AP scan (broadcast SSID)
Trying to get current scan results first without requesting a new scan to speed up initial association
Received 71 bytes of scan results (1 BSSes)
Scan results: 1
Selecting BSS from priority group 0
0: 00:04:0e:f3:d5:29 ssid='amicofrit' wpa_ie_len=26 rsn_ie_len=0 caps=0x0
  selected based on WPA IE
Trying to associate with 00:04:0e:f3:d5:29 (SSID='amicofrit' freq=0 MHz)
Cancelling scan request
WPA: clearing own WPA/RSN IE
Automatic auth_alg selection: 0x1
WPA: using IEEE 802.11i/D3.0
WPA: Selected cipher suites: group 8 pairwise 8 key_mgmt 2 proto 1
WPA: set AP WPA IE - hexdump(len=26): dd 18 00 50 f2 01 01 00 00 50 f2 02 01 00 00 50 f2 02 01 00 00 50 f2 02 00 00
WPA: clearing AP RSN IE
WPA: using GTK TKIP
WPA: using PTK TKIP
WPA: using KEY_MGMT WPA-PSK
WPA: Set own WPA IE default - hexdump(len=24): dd 16 00 50 f2 01 01 00 00 50 f2 02 01 00 00 50 f2 02 01 00 00 50 f2 02
No keys have been configured - skip key clearing
wpa_driver_wext_set_drop_unencrypted
State: SCANNING -> ASSOCIATING
wpa_driver_wext_set_operstate: operstate 0->0 (DORMANT)
WEXT: Operstate: linkmode=-1, operstate=5
wpa_driver_wext_associate
Setting authentication timeout: 10 sec 0 usec
EAPOL: External notification - EAP success=0
EAPOL: External notification - EAP fail=0
EAPOL: External notification - portControl=Auto
RTM_NEWLINK: operstate=0 ifi_flags=0x11003 ([UP][LOWER_UP])
Wireless event: cmd=0x8b06 len=8
RTM_NEWLINK: operstate=0 ifi_flags=0x11003 ([UP][LOWER_UP])
Wireless event: cmd=0x8b1a len=17
Authentication with 00:00:00:00:00:00 timed out.
Added BSSID 00:04:0e:f3:d5:29 into blacklist
State: ASSOCIATING -> DISCONNECTED
wpa_driver_wext_set_operstate: operstate 0->0 (DORMANT)
WEXT: Operstate: linkmode=-1, operstate=5
No keys have been configured - skip key clearing
EAPOL: External notification - portEnabled=0
EAPOL: External notification - portValid=0
Setting scan request: 0 sec 0 usec
State: DISCONNECTED -> SCANNING
Starting AP scan (broadcast SSID)
Scan timeout - try to get results
Received 71 bytes of scan results (1 BSSes)
Scan results: 1
Selecting BSS from priority group 0
0: 00:04:0e:f3:d5:29 ssid='amicofrit' wpa_ie_len=26 rsn_ie_len=0 caps=0x0
  selected based on WPA IE
Trying to associate with 00:04:0e:f3:d5:29 (SSID='amicofrit' freq=0 MHz)
Cancelling scan request
WPA: clearing own WPA/RSN IE
Automatic auth_alg selection: 0x1
WPA: using IEEE 802.11i/D3.0
WPA: Selected cipher suites: group 8 pairwise 8 key_mgmt 2 proto 1
WPA: set AP WPA IE - hexdump(len=26): dd 18 00 50 f2 01 01 00 00 50 f2 02 01 00 00 50 f2 02 01 00 00 50 f2 02 00 00
WPA: clearing AP RSN IE
WPA: using GTK TKIP
WPA: using PTK TKIP
WPA: using KEY_MGMT WPA-PSK
WPA: Set own WPA IE default - hexdump(len=24): dd 16 00 50 f2 01 01 00 00 50 f2 02 01 00 00 50 f2 02 01 00 00 50 f2 02
No keys have been configured - skip key clearing
wpa_driver_wext_set_drop_unencrypted
State: SCANNING -> ASSOCIATING
wpa_driver_wext_set_operstate: operstate 0->0 (DORMANT)
WEXT: Operstate: linkmode=-1, operstate=5
wpa_driver_wext_associate
Setting authentication timeout: 10 sec 0 usec
EAPOL: External notification - EAP success=0
EAPOL: External notification - EAP fail=0
EAPOL: External notification - portControl=Auto
RTM_NEWLINK: operstate=0 ifi_flags=0x11003 ([UP][LOWER_UP])
Wireless event: cmd=0x8b06 len=8
RTM_NEWLINK: operstate=0 ifi_flags=0x11003 ([UP][LOWER_UP])
Wireless event: cmd=0x8b1a len=17
Authentication with 00:00:00:00:00:00 timed out.
BSSID 00:04:0e:f3:d5:29 blacklist count incremented to 2
State: ASSOCIATING -> DISCONNECTED
wpa_driver_wext_set_operstate: operstate 0->0 (DORMANT)
WEXT: Operstate: linkmode=-1, operstate=5
No keys have been configured - skip key clearing
EAPOL: External notification - portEnabled=0
EAPOL: External notification - portValid=0
Setting scan request: 0 sec 0 usec
State: DISCONNECTED -> SCANNING
Starting AP scan (broadcast SSID)
Scan timeout - try to get results
Received 71 bytes of scan results (1 BSSes)
Scan results: 1
Selecting BSS from priority group 0
0: 00:04:0e:f3:d5:29 ssid='amicofrit' wpa_ie_len=26 rsn_ie_len=0 caps=0x0
  skip - blacklisted
No APs found - clear blacklist and try again
Removed BSSID 00:04:0e:f3:d5:29 from blacklist (clear)
Selecting BSS from priority group 0
0: 00:04:0e:f3:d5:29 ssid='amicofrit' wpa_ie_len=26 rsn_ie_len=0 caps=0x0
  selected based on WPA IE
Trying to associate with 00:04:0e:f3:d5:29 (SSID='amicofrit' freq=0 MHz)
Cancelling scan request
WPA: clearing own WPA/RSN IE
Automatic auth_alg selection: 0x1
WPA: using IEEE 802.11i/D3.0
WPA: Selected cipher suites: group 8 pairwise 8 key_mgmt 2 proto 1
WPA: set AP WPA IE - hexdump(len=26): dd 18 00 50 f2 01 01 00 00 50 f2 02 01 00 00 50 f2 02 01 00 00 50 f2 02 00 00
WPA: clearing AP RSN IE
WPA: using GTK TKIP
WPA: using PTK TKIP
WPA: using KEY_MGMT WPA-PSK
WPA: Set own WPA IE default - hexdump(len=24): dd 16 00 50 f2 01 01 00 00 50 f2 02 01 00 00 50 f2 02 01 00 00 50 f2 02
No keys have been configured - skip key clearing
wpa_driver_wext_set_drop_unencrypted
State: SCANNING -> ASSOCIATING
wpa_driver_wext_set_operstate: operstate 0->0 (DORMANT)
WEXT: Operstate: linkmode=-1, operstate=5
wpa_driver_wext_associate
Setting authentication timeout: 10 sec 0 usec
EAPOL: External notification - EAP success=0
EAPOL: External notification - EAP fail=0
EAPOL: External notification - portControl=Auto
RTM_NEWLINK: operstate=0 ifi_flags=0x11003 ([UP][LOWER_UP])
Wireless event: cmd=0x8b06 len=8
RTM_NEWLINK: operstate=0 ifi_flags=0x11003 ([UP][LOWER_UP])
Wireless event: cmd=0x8b1a len=17

[DrBrex]

prova un

iwlist wlan0 scanning

e vediamo se trova correttamente l'AP..

[maitarco]

iwlist wlan0 scanning

wlan0    Scan completed :
          Cell 01 - Address: 00:04:0E:F3:D5:29
                    ESSID:"amicofrit"
                    IE: WPA Version 1
                        Group Cipher : TKIP
                        Pairwise Ciphers (1) : TKIP
                        Authentication Suites (1) : PSK 

[DrBrex]

lo vedo un pò scarno come output...non vorrei che quel driver non fosse un granché...puoi provare il driver per win con ndiswrapper?

[maitarco]

beh, in passato lo ho usato e funzionava,
come dovrei fare per disinstallare il driver attuale?

[DrBrex]

beh, in passato lo ho usato e funzionava,
come dovrei fare per disinstallare il driver attuale?

uhm e cosa hai cambiato da quando funzionava ad adesso?
non so nemmeno cosa ha installato il driver attuale
probabilmente è un modulo che si carica, nel caso basta che lo metti in blacklist

[maitarco]

ecco fatto! (good)
con ndiswrapper tutto funziona alla perfezione!
avrei preferito caricare il driver del produttore, non c'è dubbio, ma almeno posso navigare senza fili... (e con wpasuppl. funzionante!!!
grazie di cuore a DrBrex e AleXit!!!!
se linux sta facendo (e farà ancor di più) tutto sto' casino è soprattutto grazie a persone come voi che si dedicano a a questa nobile causa.
se passate dalle parti di trieste non esitate a contattarmi che vi spetta una cena a casa mia! (b2b)
ci tengo!

[AleXit]

Ottimo.... 
Hai adesso l'onore (e l'ònere) di mettere [risolto] al titolo del topic!!

(b2b)

[DrBrex]

se passate dalle parti di trieste non esitate a contattarmi che vi spetta una cena a casa mia! (b2b)
ci tengo!

occhio che io sono (quasi) in zona e potresti rischiare :P

[AleXit]

Io sto abbastanza lontano (Toscana) ma se la cena è sostanziosa ci potrei pensare :P (b2b)