alfa awuso36H kismet

Riconoscimento, installazione e configurazione delle periferiche.
Scrivi risposta
Avatar utente
top900
Prode Principiante
Messaggi: 147
Iscrizione: lunedì 5 marzo 2007, 0:07

alfa awuso36H kismet

Messaggio da top900 »

Ho sostituito la wifi usb con una alfa AWUSO36H e non riesco a riconfigurare kismet la chiave wifi monta drivers rtl8187 il risultato del comando e' il seguente

Codice: Seleziona tutto

ubuntu@ubuntu-laptop:~$ sudo kismet
Server options:  none
Client options:  none
Starting server...
Waiting for server to start before starting UI...
Suid priv-dropping disabled.  This may not be secure.
No specific sources given to be enabled, all will be enabled.
Enabling channel hopping.
Enabling channel splitting.
FATAL: Unknown capture source type 'rtl8187' in source 'rtl8187,wlan0,rtl8187'
[1] + Done(1)                    ${BIN}/kismet_server --silent ${server}
ubuntu@ubuntu-laptop:~$ 
il file kismet.conf e' stato configurato nel modo seguente

Codice: Seleziona tutto

# Sources are defined as:
# source=sourcetype,interface,name[,initialchannel]
# Source types and required drivers are listed in the README under the
# CAPTURE SOURCES section.
# The initial channel is optional, if hopping is not enabled it can be used
# to set the channel the interface listens on.
# YOU MUST CHANGE THIS TO BE THE SOURCE YOU WANT TO USE
source=rtl8187,wlan0,rtl8187
# Comma-separated list of sources to enable.  This is only needed if you defined
# multiple sources and only want to enable some of them.  By default, all defined
# sources are enabled.
# For example:
# enablesources=rtl8187
ma non funziona ???
Ultima modifica di top900 il giovedì 24 maggio 2007, 23:05, modificato 1 volta in totale.
Avatar utente
top900
Prode Principiante
Messaggi: 147
Iscrizione: lunedì 5 marzo 2007, 0:07

Re: alfa awuso36H kismet

Messaggio da top900 »

qualcuno ha configurato kismet con i drivers realtek  ::) cosa devo scrivere help me :'(
Avatar utente
top900
Prode Principiante
Messaggi: 147
Iscrizione: lunedì 5 marzo 2007, 0:07

Re: alfa awuso36H kismet

Messaggio da top900 »

Ragazzi ho bisogno del vostro aiuto,non sono in grado di risolvere questo problema da solo,qualcuno usa i drivers rtl8187,grazie :(
Avatar utente
top900
Prode Principiante
Messaggi: 147
Iscrizione: lunedì 5 marzo 2007, 0:07

Re: alfa awuso36H kismet

Messaggio da top900 »

help.....me...... :'(
Avatar utente
top900
Prode Principiante
Messaggi: 147
Iscrizione: lunedì 5 marzo 2007, 0:07

Re: alfa awuso36H kismet

Messaggio da top900 »

Nelle spiegazioni di kismet i driver rtl8187 non sono presenti , se qualcuno usa i miei stessi driver lo prego di indicarmi come settare il fili kismet.conf  :(
kripstall
Prode Principiante
Messaggi: 3
Iscrizione: lunedì 12 febbraio 2007, 16:43

Re: alfa awuso36H kismet

Messaggio da kripstall »

in kismet.conf

source=rt8180,wlan0,rt8187

ho anche io questo usb

by
Avatar utente
top900
Prode Principiante
Messaggi: 147
Iscrizione: lunedì 5 marzo 2007, 0:07

Re: alfa awuso36H kismet

Messaggio da top900 »

ciao kripstal finalmente qualcuno che ha la mia alfa

Codice: Seleziona tutto

ubuntu@ubuntu-laptop:~$ sudo kismet
Server options:  none
Client options:  none
Starting server...
Waiting for server to start before starting UI...
Suid priv-dropping disabled.  This may not be secure.
No specific sources given to be enabled, all will be enabled.
Enabling channel hopping.
Enabling channel splitting.
Source 0 (rt8187): Enabling monitor mode for rt8180 source interface wlan0 channel 6...
FATAL: Failed to set monitor mode: Device or resource busy.  This usually means your drivers either do not support monitor mode, or use a different mechanism for getting to it.  Make sure you have a version of your drivers that support monitor mode, and consult the troubleshooting section of the README.
[1] + Done(1)                    ${BIN}/kismet_server --silent ${server}
ubuntu@ubuntu-laptop:~$ sudo gedit /etc/kismet/kismet.conf
ubuntu@ubuntu-laptop:~$ sudo kismet
Server options:  none
Client options:  none
Starting server...
Waiting for server to start before starting UI...
Suid priv-dropping disabled.  This may not be secure.
No specific sources given to be enabled, all will be enabled.
Enabling channel hopping.
Enabling channel splitting.
Source 0 (rt8187): Enabling monitor mode for rt8180 source interface wlan0 channel 6...
FATAL: Failed to set monitor mode: Device or resource busy.  This usually means your drivers either do not support monitor mode, or use a different mechanism for getting to it.  Make sure you have a version of your drivers that support monitor mode, and consult the troubleshooting section of the README.
[1] + Done(1)                    ${BIN}/kismet_server --silent ${server}
ubuntu@ubuntu-laptop:~$ 

non funge puoi aiutarmi  ???
Avatar utente
top900
Prode Principiante
Messaggi: 147
Iscrizione: lunedì 5 marzo 2007, 0:07

Re: alfa awuso36H kismet

Messaggio da top900 »

ti posto il file kismet.conf

Codice: Seleziona tutto

# Sources are defined as:
# source=sourcetype,interface,name[,initialchannel]
# Source types and required drivers are listed in the README under the
# CAPTURE SOURCES section.
# The initial channel is optional, if hopping is not enabled it can be used
# to set the channel the interface listens on.
# YOU MUST CHANGE THIS TO BE THE SOURCE YOU WANT TO USE
source=rt8180,wlan0,rt8187
# Comma-separated list of sources to enable.  This is only needed if you defined
# multiple sources and only want to enable some of them.  By default, all defined
# sources are enabled.
# For example:
# enablesources=rt8180
dimmi dove sbaglio grazie :(
Avatar utente
top900
Prode Principiante
Messaggi: 147
Iscrizione: lunedì 5 marzo 2007, 0:07

Re: alfa awuso36H kismet

Messaggio da top900 »

questo e' il risultato :'(

Codice: Seleziona tutto

ubuntu@ubuntu-laptop:~$ sudo kismet
Server options:  none
Client options:  none
Starting server...
Waiting for server to start before starting UI...
Suid priv-dropping disabled.  This may not be secure.
No specific sources given to be enabled, all will be enabled.
Enabling channel hopping.
Enabling channel splitting.
Source 0 (rt8187): Enabling monitor mode for rt8180 source interface wlan0 channel 6...
FATAL: Failed to set monitor mode: Device or resource busy.  This usually means your drivers either do not support monitor mode, or use a different mechanism for getting to it.  Make sure you have a version of your drivers that support monitor mode, and consult the troubleshooting section of the README.
[1] + Done(1)                    ${BIN}/kismet_server --silent ${server}
ubuntu@ubuntu-laptop:~$ 

help me  :( ??? ::)
Avatar utente
top900
Prode Principiante
Messaggi: 147
Iscrizione: lunedì 5 marzo 2007, 0:07

Re: alfa awuso36H kismet

Messaggio da top900 »

Scusa kripstall visto che hai la mia stessa wifi quale driver devo installare e come ?
In enablesources cosa devo scrivere? ??? :(
Avatar utente
top900
Prode Principiante
Messaggi: 147
Iscrizione: lunedì 5 marzo 2007, 0:07

Re: alfa awuso36H kismet

Messaggio da top900 »

Ragazzi aiutatemi  ::) :'(
Avatar utente
top900
Prode Principiante
Messaggi: 147
Iscrizione: lunedì 5 marzo 2007, 0:07

Re: alfa awuso36H kismet

Messaggio da top900 »

Chiedo un consiglio a chi possiede la mia stessa scheda (alfa awuso 36H ) per risolvere qhesto problema , ::) se non trovo la soluzione su questo forum sono  fritto... :( ho buttato via i soldi.....gulp  ... :(
Avatar utente
top900
Prode Principiante
Messaggi: 147
Iscrizione: lunedì 5 marzo 2007, 0:07

Re: alfa awuso36H kismet

Messaggio da top900 »

risolto con questi comandi in successione  : ifconfig wlan0 down ,, iwconfig wlan0 mode monitor ,, ifconfig wlan0 up e la usb e' andata in mode monitor (good)
Avatar utente
mat.gambak
Prode Principiante
Messaggi: 28
Iscrizione: sabato 5 giugno 2010, 11:52
Località: TV
Contatti:

Re: alfa awuso36H kismet

Messaggio da mat.gambak »

kripstall ha scritto: in kismet.conf

source=rt8180,wlan0,rt8187

ho anche io questo usb

by
GRAZIE, ho risolto mettendo  source=rt8180,wlan0,rt8187!  ;)
Scrivi risposta

Ritorna a “Driver e periferiche”

Chi c’è in linea

Visualizzano questa sezione: 0 utenti iscritti e 9 ospiti